Mazda CX-5 Service & Repair Manual: General
- Aerodynamic
- Body Panel
- Bumper Bracket Installation [Panel Replacement]
- Bumper Bracket Removal [Panel Replacement]
- Bumper Slider Removal/Installation
- Bumper Stiffener Lower Removal/Installation
- Center Under Cover Removal/Installation
- Cowl Grille Removal/Installation
- Cowl Panel Removal/Installation
- Cowl Upper Plate Installation [Panel Replacement]
- Cowl Upper Plate Removal [Panel Replacement]
- D Pillar Reinforcement (Lower) Installation [Panel Replacement]
- D Pillar Reinforcement (Lower) Removal [Panel Replacement]
- Efficient Installation Of Body Panels
- Efficient Removal Of Body Panels
- Energy Absorbing Form Removal/Installation
- Exterior Trim
- Extractor Chamber Removal/Installation
- Floor Side Panel Installation [Panel Replacement]
- Floor Side Panel Removal [Panel Replacement]
- Floor Under Cover Removal/Installation
- Front Beltline Molding Removal/Installation
- Front Bumper Disassembly/Assembly
- Front Bumper Reinforcement Removal/Installation
- Front Bumper Removal/Installation
- Front Fender Junction Installation [Panel Replacement]
- Front Fender Junction Removal [Panel Replacement]
- Front Fender Panel Removal/Installation
- Front Over Fender Removal/Installation
- Front Under Cover No.1 Removal/Installation
- Front Under Cover No.2 Removal/Installation
- Lower Cowl Side Reinforcement Installation [Panel Replacement]
- Lower Cowl Side Reinforcement Removal [Panel Replacement]
- Mudguard Removal/Installation
- Polypropylene Bumper Repair [Plastic Body Parts]
- Rear Beltline Molding Removal/Installation
- Rear Bumper Disassembly/Assembly
- Rear Bumper Reinforcement Removal/Installation
- Rear Bumper Removal/Installation
- Rear End Panel Installation [Panel Replacement]
- Rear End Panel Removal [Panel Replacement]
- Rear Fender Lower Panel Installation [Panel Replacement]
- Rear Fender Lower Panel Removal [Panel Replacement]
- Rear Fender Panel Installation [Panel Replacement]
- Rear Fender Panel Removal [Panel Replacement]
- Rear Over Fender Removal/Installation
- Rear Sash Molding Installation
- Rear Sash Molding Removal
- Rear Side Panel Installation [Panel Replacement]
- Rear Side Panel Removal [Panel Replacement]
- Rear Spoiler Removal/Installation
- Repairable Range Of Polypropylene Bumpers [Plastic Body Parts]
- Sail Garnish Removal/Installation
- Seal Board Upper Removal/Installation
- Seal Plate Removal/Installation
- Set Plate Removal/Installation
- Side Garnish Installation
- Side Garnish Removal
- Side Sill Panel Installation [Panel Replacement]
- Side Sill Panel Removal [Panel Replacement]
- Side Step Molding Removal/Installation
- Speaker Grille Removal/Installation
- Splash Shield Removal/Installation
- Underbody Dimensions [Dimensions]
- Upper Cowl Side Reinforcement Installation [Panel Replacement]
- Upper Cowl Side Reinforcement Removal [Panel Replacement]
- Ventilator Grille Removal/Installation
Aerodynamic
Purpose/Function
For improved aerodynamics, under covers are installed to the under-surface
of the vehicle.
Construction
The vehicle is equipped with the following (3) under cov ...
Other materials:
Oil Cooler Removal/Installation [Fw6 A EL, Fw6 Ax EL]
1. Disconnect the negative battery cable..
2. Remove the front under cover No.2..
3. Drain the ATF..
4. Drain the engine coolant..
5. Remove in the order indicated in the table.
1
Water hose (connected to the water pipe)
2
Water hose ...
Mass Air Flow (MAF) Sensor Inspection
Visual Inspection
1. Remove the MAF sensor/IAT sensor No.1..
2. Visually inspect the MAF sensor for the following:
Damage, cracks, soiling
Rusted sensor terminal
Bent sensor terminal
If there is any malfunction, repair or replace the MAF sensor/IAT sensor
...
Switch Panel Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the car-navigation unit. (with car-navigation system).
3. Insert your hand from the lower side of the lower panel (without car-navigation
system) or the area where the car-navigation unit was installed (with car-navigation
system), press t ...
