Mazda CX-5 Service & Repair Manual: Accessories
- Cruise Control
- Cruise Control Switch Inspection
- Cruise Control System
- Cruise Main Indicator Light (Amber)
- Cruise Set Indicator Light (Green)
- Electronics
- Power Sockets
- Accessory Socket
- Center Accessory Socket Inspection
- Center Accessory Socket Removal/Installation
- Front Accessory Socket Inspection
- Front Accessory Socket Removal/Installation
- Rear Accessory Socket Inspection
- Rear Accessory Socket Removal/Installation
- Safety Systems
- Active Command Modes Inspection [Blind Spot Monitoring (Bsm)]
- Blind Spot Monitoring (Bsm) Bracket Removal/Installation
- Blind Spot Monitoring (Bsm) Control Module
- Blind Spot Monitoring (Bsm) Control Module Inspection
- Blind Spot Monitoring (Bsm) Control Module Removal/Installation
- Blind Spot Monitoring (Bsm) Off Indicator Light
- Blind Spot Monitoring (Bsm) Off Switch
- Blind Spot Monitoring (Bsm) Off Switch Inspection
- Blind Spot Monitoring (Bsm) System
- Blind Spot Monitoring (Bsm) Warning Alarm
- Bsm Indicator Light Does Not Flash While Under Bsm Indicator Light Flashing Conditions (With Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
- Bsm Indicator Light Flashes While Not Under Bsm Indicator Light Flashing Conditions (No Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
- PID/Data Monitor Inspection [Blind Spot Monitoring (Bsm)]
- Security & Keyless Entry
- Remote Transmitter Battery Voltage Inspection
- Theft Deterrent Horn Inspection
- Theft Deterrent Horn Removal/Installation
- Sensors, Switches, Relays
- Entry System
- Ignition Switch, Steering Lock
- Storage
- Afs Off Indicator Light
- Air Bag System Warning Light [Standard Deployment Control System]
- Air Bag System Warning Light [Two Step Deployment Control System]
- Automatic Transaxle Warning Light [Fw6 A EL, Fw6 Ax EL]
- Awd Warning Light
- Blind Spot Monitoring (Bsm) Off Indicator Light
- Brake System/ABS Warning Light
- Bsm Indicator Light Does Not Flash While Under Bsm Indicator Light Flashing Conditions (With Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
- Bsm Indicator Light Flashes While Not Under Bsm Indicator Light Flashing Conditions (No Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
- Charging System Warning Light
- Check Fuel Cap Warning Light
- Cruise Main Indicator Light (Amber)
- Cruise Set Indicator Light (Green)
- Door Ajar Warning Light
- Engine Oil Pressure Warning Light
- Front Fog Lights Indicator Light
- Gear Position Indicator [Fw6 A EL, Fw6 Ax EL]
- Headlight High Beam Indicator Light
- Key Warning Light (Red)/Key Indicator Light (Green)
- Lights On Indicator Light
- Lights On Reminder Warning Alarm
- Low Engine Coolant Temperature Indicator Light (Blue)/High Engine Coolant Temperature Warning Light (Red)
- Low Fuel Warning Light
- Master Warning Light
- Panel Light Control Indicator Alarm
- Power Steering Malfunction Indicator Light
- Seat Belt Warning Alarm
- Seat Belt Warning Light
- Security Indicator Light
- Shift Position Indicator Light [Fw6 A EL, Fw6 Ax EL]
- Tcs Off Switch, Tcs Off Indicator Light
- Tcs/DSC Indicator Light
- Tire Pressure Monitoring System Warning Light
- Turn And Hazard Indicator Alarm
- Turn Signal/Hazard Warning Indicator Lights
- Trailer
Cruise Control
...
Other materials:
Cruise Main Indicator Light (Amber)
Purpose/Function
Illuminates while the cruise control system is in standby mode to inform
the driver that the cruise control system is on standby.
Construction
Built into the instrument cluster.
Operation
Illuminates while the cruise control system is on sta ...
Rear Crossmember Removal/Installation [Awd]
WARNING:
Verify that the crossmember is securely supported by a jack. If the rear
crossmember falls off, it can cause serious injury or death, and damage to the
vehicle.
CAUTION:
Performing the following procedures without first removing the rear ABS wheel-speed
sensor ...
Glass Antenna Inspection
1. Disconnect the negative battery cable..
2. Partially peel back the seaming welt.
3. Remove the liftgate upper trim..
4. Disconnect antenna feeder No.3 connector..
5. Visually inspect the glass antenna for damage.
6. Verify that the continuity between the glass antenna terminals is as in ...
