Mazda CX-5 Service & Repair Manual: Frame
- Body Sealing [Water Proof And Rust Preventive]
- Cabin Side Frame Straight Line Dimensions [Dimensions]
- Center Pillar Installation [Panel Replacement]
- Center Pillar Removal [Panel Replacement]
- Construction Standard Values [Construction Standard Values]
- Corner Plate Installation [Panel Replacement]
- Corner Plate Removal [Panel Replacement]
- Dumping Sheet Replacement [Water Proof And Rust Preventive]
- Front Body Straight Line Dimensions (1) [Dimensions]
- Front Body Straight Line Dimensions (2) [Dimensions]
- Front Crossmember Removal/Installation
- Front Frame (Rear) Installation [Panel Replacement]
- Front Frame (Rear) Removal [Panel Replacement]
- Front Pillar Installation [Panel Replacement]
- Front Pillar Removal [Panel Replacement]
- Front Seat Cushion Frame Removal/Installation
- Front Side Frame (Partial Cutting) Installation [Panel Replacement]
- Front Side Frame (Partial Cutting) Removal [Panel Replacement]
- Front Side Frame Installation [Panel Replacement]
- Front Side Frame Removal [Panel Replacement]
- Rear Body Straight Line Dimensions (1) [Dimensions]
- Rear Crossmember Removal/Installation [2 Wd]
- Rear Crossmember Removal/Installation [Awd]
- Rear Pillar (Outer) Installation [Panel Replacement]
- Rear Pillar (Outer) Removal [Panel Replacement]
- Rear Seat Back Frame Removal/Installation
- Rear Side Frame Installation [Panel Replacement]
- Rear Side Frame Removal [Panel Replacement]
- Room Straight Line Dimensions (1) [Dimensions]
- Room Straight Line Dimensions (2) [Dimensions]
- Room Straight Line Dimensions (3) [Dimensions]
- Rust Preventive Treatment [Water Proof And Rust Preventive]
- Side Member Installation [Panel Replacement]
- Side Member Removal [Panel Replacement]
- Torque Box Installation [Panel Replacement]
- Torque Box Removal [Panel Replacement]
- Ultra High Tension Steel [Construction]
- Under Coating [Water Proof And Rust Preventive]
Ventilator Grille Removal/Installation
Side Ventilator Grille
Driver-side
1. Disconnect the negative battery cable..
2. Remove the switch panel..
3. Insert your hand from the area where the switch panel was installed, remove
the si ...
Body Sealing [Water Proof And Rust Preventive]
Sealant is applied to the parts where the panels meet and to the hemmed parts
of the door panel and hood panel to provide water proofing and rust proofing.
...
Other materials:
Manifold Absolute Pressure (Map) Sensor/Intake Air Temperature (Iat) Sensor
No.2 Removal/Installation
NOTE:
Because the IAT sensor No.2 is integrated in the MAP sensor, replacing the
IAT sensor No.2 includes replacement of the MAP sensor/IAT sensor No.2.
1. Disconnect the negative battery cable..
2. Disconnect the MAP sensor/IAT sensor No.2 connector.
3. Remove the MAP sensor/IA ...
2 6 Brake [Fw6 A EL, Fw6 Ax EL]
Purpose/Function
The 2-6 brake locks the rear internal gear and reduction planetary carrier
while in 2GR and 6GR.
Construction
The 2-6 brake consists of the following parts shown in the figure.
The driven plate of the 2-6 brake does not rotate because it is c ...
Front Drive Shaft (Tripod Joint) Disassembly/Assembly
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
1
Boot band (transaxle side (large diameter))
(See Boot Band (Transaxle Side (Large Diameter)) Disassembly Note.)
(See Boot Band (Transaxle Side (Large Diameter) ...
