Mazda CX-5 Service & Repair Manual: Brakes
- General
- 2 6 Brake [Fw6 A EL, Fw6 Ax EL]
- Brake Fluid Air Bleeding
- Brake Fluid Inspection
- Brake Fluid Pressure Sensor
- Brake Fluid Pressure Sensor Inspection
- Brake Hose (Front) Removal/Installation
- Brake Hose (Rear) Removal/Installation
- Brake Pedal
- Brake Pedal Inspection
- Brake Pedal Removal/Installation
- Brake/Taillight Bulb Removal/Installation
- Brakes
- Brakes SST
- Conventional Brake System
- Disc Pad (Front) Replacement
- Disc Pad (Rear) Replacement
- General Procedures (Brake)
- Low And Reverse Brake [Fw6 A EL, Fw6 Ax EL]
- Master Cylinder
- Master Cylinder
- Master Cylinder Removal/Installation
- Power Brake Unit
- Power Brake Unit Inspection
- Power Brake Unit Removal/Installation
- R 3 5 Brake [Fw6 A EL, Fw6 Ax EL]
- Vacuum Hose Removal/Installation
- Vacuum Line Inspection
- Vacuum Pump Inspection
- Vacuum Pump Removal/Installation
- Vacuum Pump [Skyactiv G 2.0]
- Brake Control, Vehicle Dynamics
- General Information
- ABS
- Sensors, Switches, Relays
- Disc Brakes
- Caliper (Front) Disassembly/Assembly
- Caliper (Rear) Disassembly/Assembly
- Front Brake (Disc)
- Front Brake (Disc) Inspection
- Front Brake (Disc) Removal/Installation
- Rear Brake (Disc)
- Rear Brake (Disc) Inspection
- Rear Brake (Disc) Removal/Installation
- Parking Brake
- Front Parking Brake Cable Removal/Installation
- Parking Brake Lever Adjustment
- Parking Brake Lever Inspection
- Parking Brake Lever Removal/Installation
- Parking Brake System
- Rear Parking Brake Cable Removal/Installation
- Parking Brake Switch Inspection
- Sensors, Switches, Relays
- Brake Fluid Level Sensor Inspection
- Brake Switch Inspection
- Turbine/Input Shaft Speed Sensor, Output Shaft Speed Sensor [Fw6 A EL, Fw6 Ax
EL]
1. Disconnect the negative battery cable..
2. Spread open the rain sensor cover in the direction of the arrows (1) and disengage
tabs A to remove it.
3. Disconnect the rain sensor connector ...
Other materials:
Front Bumper Reinforcement Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Seal board upper.
b. Front bumper.
c. Front combination light.
d. Set plate.
e. Energy-absorbing form.
f. Front under cover No.1.
g. Bumper stiffener lower.
3. Support the shroud panel using a jack.
CAUT ...
Brake Hose (Rear) Removal/Installation
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
3. After installation, add brake fluid, bleed the air, and inspect for fluid
leakage..
1
Brake pipe
2
Clip
3
Bolt
...
Liftgate Latch And Lock Actuator Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Liftgate upper trim.
b. Liftgate side trim.
c. Liftgate lower trim.
3. Disconnect the connector.
4. Remove the bolts.
5. Remove the liftgate latch and lock actuator from the liftgate.
6. Install in t ...
© 2016-2025 Copyright www.mcx5.org
