Mazda CX-5 Service & Repair Manual
Mazda CX-5 Service & Repair Manual
- Vehicle General
- How To Use This Manual
- Abbreviations
- Body And Accessories SST
- Front Wiring Harness Protector Removal/Installation
- Identification Number Locations
- Jacking Positions, Vehicle Lift (2 Supports) And Safety Stand (Rigid Rack) Positions
- Personalization Features
- Pre Delivery Inspection
- Push Button Start Inspection
- Push Button Start Removal/Installation
- Sae Standards
- Service Cautions
- St 001/12 Special Service Tool Shipment January 2013
- Units
- Vehicle Identification Number (VIN) Code
- Accessories
- Cruise Control
- Electronics
- Power Sockets
- Safety Systems
- Security & Keyless Entry
- Storage
- Trailer
- Body
- Doors/Lids & Hood/Trunk
- Body Exterior, Frame
- Glass & Windows
- Horn
- Driver Info & Control
- Body Interior
- Lighting & Horn
- Mirrors
- Roof - Fixed, Leisure
- Seats
- Wipers, Washers
- Brakes
- General
- Brake Control, Vehicle Dynamics
- Disc Brakes
- Parking Brake
- Sensors, Switches, Relays
- Drivetrain
- Driveline
- Transmission/Transaxle
- Electrical
- General
- Battery
- Fuses & Junction Blocks
- Ground Distribution
- Ignition
- Data Network
- Starting, Charging
- Engine
- General
- Belts, Hoses, Pulleys
- Control
- Cooling
- Emissions
- Engine Assembly
- Exhaust & Emissions
- Forced Induction
- Fuel
- Intake
- Lubrication
- HVAC
- General
- A/C
- Restraints
- Restraints
- Restraints SST
- Adjuster Anchor Removal/Installation
- Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Standard Deployment
Control System]
- Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Two Step Deployment
Control System]
- Air Bag Module And Pre Tensioner Seat Belt Disposal Procedures [Standard Deployment
Control System]
- Air Bag Module And Pre Tensioner Seat Belt Disposal Procedures [Two Step Deployment
Control System]
- Buckle Switch Inspection
- Front Buckle Removal/Installation
- Front Seat Belt Removal/Installation
- Lap Pre Tensioner Seat Belt [Two Step Deployment Control System]
- Pre Tensioner Seat Belt [Standard Deployment Control System]
- Pre Tensioner Seat Belt [Two Step Deployment Control System]
- Rear Buckle Removal/Installation
- Rear Seat Belt Removal/Installation
- Seat Belt
- Seat Belt Inspection
- Steering
- General
- Linkage, Power
- Wheel, Column
- Suspension
- General
- Front Suspension
- Rear Suspension
- Wheels, Tires
Personalization Features
...
Other materials:
Meter Hood Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the upper column cover.
3. Using a phillips screwdriver, remove fasteners.
NOTE:
When pulling up the shaft of fasteners using a phillips screwdriver, the
shaft will not be pulled up if it is rotated by pressing the driver. To pull ...
Reporting Safety Defects (U.S.A.)
If you believe that your vehicle has a defect which could cause a crash or could
cause injury or death, you should immediately inform the National Highway Traffic
Safety Administration (NHTSA) in addition to notifying Mazda Motor Corporation (Your
Mazda Importer/Distributor).
If NHTSA receive ...
Exhaust System
Purpose, Outline
A 4-2-1 exhaust system has been adopted which reduces residual gas in the
cylinders using the scavenging effect and contributes to a high compression
ratio.
The loop structure of the exhaust pipes for the 4-2-1 system takes up less
space.
Structural Vie ...
© 2016-2026 Copyright www.mcx5.org
