Mazda CX-5 Service & Repair Manual: Units
|
Electric current |
A (ampere) |
|
Electric power |
W (watt) |
|
Electric resistance |
ohm |
|
Electric voltage |
V (volt) |
|
Length |
mm (millimeter) |
|
in (inch) |
|
|
Negative pressure |
kPa (kilo pascal) |
|
mmHg (millimeters of mercury) |
|
|
inHg (inches of mercury) |
|
|
Positive pressure |
kPa (kilo pascal) |
|
kgf/cm2 (kilogram force per square centimeter) |
|
|
psi (pounds per square inch) |
|
|
Number of revolutions |
rpm (revolutions per minute) |
|
Torque |
N·m (Newton meter) |
|
kgf·m (kilogram force meter) |
|
|
kgf·cm (kilogram force centimeter) |
|
|
ft·lbf (foot pound force) |
|
|
in·lbf (inch pound force) |
|
|
Volume |
L (liter) |
|
US qt (U.S. quart) |
|
|
Imp qt (Imperial quart) |
|
|
ml (milliliter) |
|
|
cc (cubic centimeter) |
|
|
cu in (cubic inch) |
|
|
fl oz (fluid ounce) |
|
|
Weight |
g (gram) |
|
oz (ounce) |
Conversion From SI Units
-
All numerical values in this manual are based on SI units. Numbers shown in conventional units are converted from these values.
Number Of Digits For Converted Values
-
The number digits for converted values is the same as the number of significant figures*1 of the SI unit.
-
For the torque value, the number of significant figures is, in principle, is 2 digits, in consideration of market practicalities.However, if the number of decimal places at the upper and lower limits of the converted value differs, the one with least number of decimal places is used. In addition, if the integer part is 3 digits or more, the integer part becomes the significant number of figures.
Converted Value Rounding Off And Rounding Up/down
-
If there is no tolerance in the SI unit value, after conversion, rounding off is to within the number of significant digits.
-
If there is tolerance in the SI unit value and the figure after conversion indicates the upper limit, the number of digits is rounded down to within the number of significant figures. If it indicates the lower limit, they are rounded up to within the number of significant figures.
-
Even if the SI unit value is the same, the converted value may differ based on whether that value is the upper or lower limit.
St 001/12 Special Service Tool Shipment January 2013
APPLICABLE MODEL(S)/VINS
2014 Mazda6
2014 CX-5
DESCRIPTION/PRICING
In support of the new 2014 Mazda6 and the 2014 CX-5, Mazda will ship to all dealers
one (1) new Special Service Tool (SST). The ...
Other materials:
Front Scuff Plate Removal/Installation
1. Take the shaded area shown in the figure, detach tab A while pulling the front
scuff plate in the direction of the arrow (1) shown in the figure, then detach the
hook B, clip C, and pin D while pulling in the direction of the arrow (2).
2. Take the shaded area shown in the figure, detach ta ...
DSC Related Parts Sensor Initialization Procedure
WARNING:
If the initialization procedure is not completed, the DSC will not operate
properly and it might cause an unexpected accident. Therefore, after replacing
or removing the DSC HU/CM or SAS control module, make sure to perform the initialization
procedure to insure proper DSC ...
Upper Cowl Side Reinforcement Removal [Panel Replacement]
Symbol Mark
Removal Procedure
1. Drill the 13 locations indicated by (A) shown in the figure.
2. Drill the 8 locations indicated by (B) shown in the figure.
NOTE:
When a drill the 8 locations indicated by (B) shown in the figure, the through
hole is not made in consideration of ...
