Mazda CX-5 Service & Repair Manual
Mazda CX-5 Service & Repair Manual
- Vehicle General
- How To Use This Manual
- Abbreviations
- Body And Accessories SST
- Front Wiring Harness Protector Removal/Installation
- Identification Number Locations
- Jacking Positions, Vehicle Lift (2 Supports) And Safety Stand (Rigid Rack) Positions
- Personalization Features
- Pre Delivery Inspection
- Push Button Start Inspection
- Push Button Start Removal/Installation
- Sae Standards
- Service Cautions
- St 001/12 Special Service Tool Shipment January 2013
- Units
- Vehicle Identification Number (VIN) Code
- Accessories
- Cruise Control
- Electronics
- Power Sockets
- Safety Systems
- Security & Keyless Entry
- Storage
- Trailer
- Body
- Doors/Lids & Hood/Trunk
- Body Exterior, Frame
- Glass & Windows
- Horn
- Driver Info & Control
- Body Interior
- Lighting & Horn
- Mirrors
- Roof - Fixed, Leisure
- Seats
- Wipers, Washers
- Brakes
- General
- Brake Control, Vehicle Dynamics
- Disc Brakes
- Parking Brake
- Sensors, Switches, Relays
- Drivetrain
- Driveline
- Transmission/Transaxle
- Electrical
- General
- Battery
- Fuses & Junction Blocks
- Ground Distribution
- Ignition
- Data Network
- Starting, Charging
- Engine
- General
- Belts, Hoses, Pulleys
- Control
- Cooling
- Emissions
- Engine Assembly
- Exhaust & Emissions
- Forced Induction
- Fuel
- Intake
- Lubrication
- HVAC
- General
- A/C
- Restraints
- Restraints
- Restraints SST
- Adjuster Anchor Removal/Installation
- Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Standard Deployment
Control System]
- Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Two Step Deployment
Control System]
- Air Bag Module And Pre Tensioner Seat Belt Disposal Procedures [Standard Deployment
Control System]
- Air Bag Module And Pre Tensioner Seat Belt Disposal Procedures [Two Step Deployment
Control System]
- Buckle Switch Inspection
- Front Buckle Removal/Installation
- Front Seat Belt Removal/Installation
- Lap Pre Tensioner Seat Belt [Two Step Deployment Control System]
- Pre Tensioner Seat Belt [Standard Deployment Control System]
- Pre Tensioner Seat Belt [Two Step Deployment Control System]
- Rear Buckle Removal/Installation
- Rear Seat Belt Removal/Installation
- Seat Belt
- Seat Belt Inspection
- Steering
- General
- Linkage, Power
- Wheel, Column
- Suspension
- General
- Front Suspension
- Rear Suspension
- Wheels, Tires
Personalization Features
...
Other materials:
Front Drive Shaft Inspection
1. Inspect the connections for any looseness.
If there is any malfunction, tighten or replace the applicable part.
2. Inspect the dust boot for damage and cracks.
If there is any malfunction, replace the applicable part.
3. Move the spline and joint up and down, left ...
Air Intake Actuator [Full Auto Air Conditioner]
Purpose
The air intake actuator moves the air intake door in the blower unit to switch
the air intake port.
Function
The air intake actuator drives the motor based on the signal from the climate
control unit and moves the air intake door to the FRESH or REC position.
...
Purge Solenoid Valve Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the plug hole plate..
3. Remove the air cleaner and air hose as a single unit..
4. Disconnect the high pressure fuel pump connector.
5. Disconnect the harness clip as shown in the figure.
6. Remove in the order indicated in the table ...
© 2016-2024 Copyright www.mcx5.org