Mazda CX-5 Service & Repair Manual: Manual
- Inspection After Manual Transaxle Overhaul [C66 M R]
- Manual Transaxle Oil Inspection [C66 M R]
- Manual Transaxle Oil Replacement [C66 M R]
- Manual Transaxle Removal/Installation [C66 M R]
- Manual Transaxle Shift Mechanism Removal/Installation [C66 M R]
- Manual Transaxle [C66 M R]
- Neutral Switch Removal/Installation [C66 M R]
- Powertrain System [C66 M R]
- Shift And Select Mechanism [C66 M R]
- Shift Control Module Removal/Installation [C66 M R]
- Synchronizer Mechanism [C66 M R]
- Turbine/Input Shaft Speed Sensor, Output Shaft Speed Sensor [Fw6 A EL, Fw6 Ax EL]
- Clutch Cover Inspection [C66 M R]
- Clutch Disc Inspection [C66 M R]
- Clutch Fluid Inspection [C66 M R]
- Clutch Fluid Leakage Inspection [C66 M R]
- Clutch Fluid Replacement/Air Bleeding [C66 M R]
- Clutch Master Cylinder Removal/Installation [C66 M R]
- Clutch Pedal Inspection [C66 M R]
- Clutch Pedal Position (CPP) Switch Inspection [Skyactiv G 2.0]
- Clutch Pedal Position (CPP) Switch [Skyactiv G 2.0]
- Clutch Pedal Position Switch Removal/Installation [C66 M R]
- Clutch Pedal Removal/Installation [C66 M R]
- Clutch Pipe And Hose Removal/Installation [C66 M R]
- Clutch Release Collar Inspection [C66 M R]
- Clutch Release Cylinder Removal/Installation [C66 M R]
- Clutch Unit Removal/Installation [C66 M R]
- Clutch [C66 M R]
- Flywheel Inspection [C66 M R]
- Low Clutch [Fw6 A EL, Fw6 Ax EL]
- Magnet Clutch [Full Auto Air Conditioner]
- Magnet Clutch [Manual Air Conditioner]
- Pilot Bearing Inspection [C66 M R]
Turbine/Input Shaft Speed Sensor, Output Shaft Speed Sensor [Fw6 A EL, Fw6 Ax
EL]
Purpose/Function
The turbine/input shaft speed sensor detects the rotation speed of the input
shaft (low clutch drum).
The output shaft speed sensor detects the rotation speed of the ...
Inspection After Manual Transaxle Overhaul [C66 M R]
1. After warming up the engine, drive the vehicle and inspect the following items:
a. No abnormal noise in each shift position.
b. Smooth shift operation when shifting gears.
c. No gear slipout ...
Other materials:
Room Straight Line Dimensions (3) [Dimensions]
Point symbol
Designation
Hole diameter or bolt or nut size mm {in}
A
Rear seat installation hole
?14 {0.55}
B
D-pillar trim installation hole
?8.6 {0.34}
...
Air Intake Actuator Inspection [Full Auto Air Conditioner]
1. Connect battery positive voltage to air intake actuator terminal B (or C),
connect terminal C (or B) to ground, and then verify that the air intake actuator
operates as shown in the table.
If the operation condition is not normal, replace the air intake actuator.
...
Front ABS Wheel Speed Sensor Removal/Installation
1. Remove the mudguard..
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
4. After installation, verify that there is no twisting in the front ABS wheel-speed
sensor.
1
Connector
2
Bolt
...
