Mazda CX-5 Service & Repair Manual: Shift Lock System Inspection
Shift-Lock System Inspection
1. Switch the ignition ON (engine off).
2. Shift the selector lever to the P position.
3. Verify that the selector lever cannot be shifted from P to R position when the brake pedal is released.
-
If it can be verified, go to the next step.
-
If not as verified, inspect the following parts:
-
Shift-lock solenoid.
-
Not P position switch.
-
Brake switch.
-
Start stop unit.
-
PCM.
4. Verify that the selector lever can be shifted from P to R position when the brake pedal is depressed.
-
If it can be verified, go to the next step.
-
If not as verified, inspect the following parts:
-
Shift-lock solenoid.
-
Not P position switch.
-
Brake switch.
-
Start stop unit.
-
PCM.
Shift-Lock Solenoid Inspection
NOTE:
-
The shift-lock solenoid is built into the selector lever component.
1. Disconnect the negative battery cable..
2. Remove the front console..
3. Reconnect the negative battery cable..
4. Verify that the voltages of each of the selector lever component terminals are as indicated in the table.
Shift-lock solenoid specification
|
Terminal |
Connected to |
Test condition |
Voltage (V) |
|
A |
IG1 relay |
Ignition switched ON (engine on) |
B+ |
|
Except above |
Below 1.0 |
||
|
H |
Start stop unit |
Under any condition |
Below 1.0 |
-
If the voltage is not as indicated in the table, repair or replace the related wiring harness.
-
If the voltage can be verified as indicated in the table, replace the selector lever component..
Shift-lock Override Button Inspection
1. Switch the ignition to off.
2. Verify that the selector lever is in the P position.
3. Without the brake pedal depressed, verify that the selector lever cannot be shifted from the P position.
4. Remove the emergency override hole cover using a tape-wrapped flathead screwdriver.
5. Insert the flathead screwdriver into the emergency override hole and push it down.
6. Verify that the selector lever can be shifted from the P position.
-
If not as verified, replace the selector lever..
Shift Control Module Removal/Installation [C66 M R]
Removal
1. Shift the shift lever to the neutral position.
2. Remove the plug hole plate..
3. Disconnect the negative battery cable..
4. Remove the air cleaner and air hose as a single unit..
...
Shift Lock System [Fw6 A EL, Fw6 Ax EL]
Purpose, Function
The shift-lock system operates when the ignition is switched to ON and the
brake pedal is not depressed, and inhibits the selector lever from being shifted
from the P po ...
Other materials:
Front Door Key Cylinder Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the service hole cover.
3. Detach the screw from the front door key cylinder.
NOTE:
The screw cannot be removed because the front outer handle bracket has a
stopper which prevents the screw from falling.
4. While pre ...
Wiper And Washer Switch Removal/Installation
1. Switch the ignition ON (engine off or on).
2. Open the driver's door.
3. Switch the ignition OFF.
4. Disconnect the negative battery cable..
5. Remove the column cover..
6. Rotate the steering wheel in the direction of the arrow shown in the figure
to the angle where the service h ...
Differential Oil Replacement
1. Place the vehicle on level ground.
2. Remove the filler plug.
3. Remove the drain plug and drain the differential oil into a container.
4. Install a new washer and the drain plug, and tighten.
Tightening torque
40—53 N·m {4.1—5.4 kgf·m, 30—39 ft·lbf}
5. Add the ...
