Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Rear Combination Light

Purpose

Function


Operation switch

Related light

Operation condition

Light switch (TNS)

Taillight

Turns on

Rear side marker light

Turns on

Brake switch

Brake light

Turns on

Turn switch

Rear turn light

Flashes

Hazard warning switch


Construction


Operation

Taillights

1. When the light switch is operated to the TNS position, a TNS signal is input to the start stop unit.

2. The start stop unit sends the TNS signal to the front body control module (FBCM).

3. When the front body control module (FBCM) receives the TNS signal. it turns the TNS relay on.

4. When the TNS relay turns on, the taillight bulbs are illuminated.


Brake lights

1. When the brake pedal is depressed, the brake light switch turns on.

2. When the brake light switch turns on, the brake lights are illuminated.


Rear turn lights (turn)

1. When the turn switch is operated to the RH position, a turn RH signal is input to the start stop unit.

2. When the turn switch is operated to the LH position, a turn LH signal is input to the start stop unit.

3. The start stop unit sends the turn RH or LH signal to the front body control module (FBCM).

4. When the front body control module (FBCM) receives the turn RH signal, the rear turn light (RH) flashes.

5. When the front body control module (FBCM) receives the turn LH signal, the rear turn light (LH) flashes.


Rear turn lights (hazard warning)

1. When the hazard warning switch is turned on, a hazard signal is input to the start stop unit.

2. The start stop unit sends a hazard warning signal to the front body control module (FBCM).

3. When the front body control module (FBCM) receives the hazard warning signal, the rear turn lights (RH) and (LH) flash.


Rear side marker lights

1. When the light switch is operated to the TNS position, a TNS signal is input to the start stop unit.

2. The start stop unit sends the TNS signal to the front body control module (FBCM).

3. When the front body control module (FBCM) receives the TNS signal. it turns the TNS relay on.

4. When the TNS relay turns on, the rear side marker lights are illuminated.


Fail-safe

PID/Data Monitor Inspection [Adaptive Front Lighting System (Afs)]
1. Connect the M-MDS to the DLC-2. 2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS. a. Select “DataLogger”. b. Select “Modules ...

Rear Combination Light Removal/Installation
NOTE: Fogging or condensation on the inside of the rear combination lights may occur due to a natural phenomenon occurring as a result of a temperature difference between the interior an ...

Other materials:

Differential Oil Temperature Sensor Inspection
WARNING: Hot differential oil may cause severe burns. Do not perform maintenance while differential oil is hot. 1. Disconnect the negative battery cable. 2. Disconnect the differential oil temperature sensor connector and remove the differential oil temperature sensor. 3. Wrap ...

Fuel Filler Lid Opener Cable Removal/Installation
1. Disconnect the negative battery cable.. 2. Remove the following parts: a. Front scuff plate (LH). b. Front seat (LH). c. Rear scuff plate. d. B-pillar lower trim (LH). e. Rear seat (4:2:4 split type). f. Rear seat cushion (6:4 split type). g. Rear seat back (6:4 split type). h. ...

Power Brake Unit Inspection
NOTE: The following inspection methods are simple inspection methods to judge the function of the power brake unit. If there is any malfunction in the power brake unit, replace the power brake unit as a single unit. Without Using SST Operation inspection 1. With the eng ...

© 2016-2025 Copyright www.mcx5.org