Mazda CX-5 Service & Repair Manual: Personalization Features

Mazda CX-5 Service & Repair Manual / Vehicle General / Personalization Features

The following systems can be customized.
When performing a customized setting, refer to the referenced section for the detailed setting procedure.

Security And Locks

NOTE:

There are two types of customization procedures; one using the M-MDS and the other using the audio unit screen.

Advanced keyless entry system


Personalization features	Setting contents	Setting procedure
The advanced keyless entry system and push button start system functions can be disabled.	Enabled./Disabled.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The out-of-area (reception area) type auto lock function can be set.	Not Adopted./OFF/ON	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
	OFF/ON	Audio unit screen is used for the setting. (See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	Not Adopted./30 seconds/60 seconds/90 seconds	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
	30 seconds/60 seconds/90 seconds	Audio unit screen is used for the setting. (See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)
The keyless beeper volume can be adjusted.	Not Adopted./Off/Low/Medium/High	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The keyless beeper volume can be adjusted.	Off/Low/Medium/High	Audio unit screen is used for the setting. (See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)

Keyless entry system


Personalization features	Setting contents	Setting procedure
The keyless entry system and push button start system functions can be disabled.	Enabled./Disabled.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	Not Adopted./30 seconds/60 seconds/90 seconds	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
	30 seconds/60 seconds/90 seconds	Audio unit screen is used for the setting. (See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)

Power door lock system


Personalization features	Setting contents	Setting procedure
2-step unlocking system can be set.	Not Adopted. / Touch Once: ALL Doors. / Once Driver's, Twice: All Doors.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
2-step unlocking system can be set.	Touch Once: ALL Doors. / Once Driver's, Twice: All Doors.	Audio unit screen is used for the setting. (See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)
Auto door lock function can be changed.	Not Adopted. / OFF / Lock When Driving. / Lock: Driving, Unlock: IGN Off. / Lock When Shifting Out Of P. / Lock: Shift From P, Unlock: In P.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
Auto door lock function can be changed.	OFF / Lock When Driving. / Lock: Driving, Unlock: IGN Off. / Lock When Shifting Out Of P. / Lock: Shift From P, Unlock: In P.	Audio unit screen is used for the setting. (See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lighting Systems

Auto light system

NOTE:

There are two types of customization procedures; one using the M-MDS and the other using the audio unit screen.

Personalization features

Setting contents

Setting procedure

Auto light sensor sensitivity can be changed.

Not Adopted./Dark/Medium Dark/Medium/Medium Light/Light

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Light/Medium Light/Medium/Medium Dark/Dark

Audio unit screen is used for the setting.

(See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)

Auto light OFF system

NOTE:

There are two types of customization procedures; one using the M-MDS and the other using the audio unit screen.

Personalization features

Setting contents

Setting procedure

The headlight emitted time of the auto light off timer can be changed.

Not Adopted. / 0 seconds. / 30 seconds. / 60 seconds. / 90 seconds. / 120 seconds.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

120 seconds. / 90 seconds. / 60 seconds. / 30 seconds. / 0 seconds.

Audio unit screen is used for the setting.

(See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)

Turn light system

NOTE:

There are two types of customization procedures; one using the M-MDS and the other using the audio unit screen.

Personalization features

Setting contents

Setting procedure

The turn light system can be switched between operable and inoperable.

Not Adopted./OFF/ON

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On/Off

Audio unit screen is used for the setting.

(See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)

Room light control system

NOTE:

There are two types of customization procedures; one using the M-MDS and the other using the audio unit screen.


Personalization features	Setting contents	Setting procedure
The front/rear map light illumination time after any door is open can be changed.	Not Adopted./30 minutes./60 minutes./10 minutes.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
	60 minutes/30 minutes/10 minutes	Audio unit screen is used for the setting. (See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)
The front/rear map light illumination time after any door is closed can be changed.	Not Adopted./15 seconds./7.5 seconds./30 seconds./60 seconds.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
	60 seconds/30 seconds/15 seconds/7.5 seconds	Audio unit screen is used for the setting. (See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)

DRL system (Except canada specs.)


Personalization features	Setting contents	Setting procedure
The DRL system Function can be set.	OFF (DRL non-illumination)/ON (DRL illumination)	(See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Wiper/Washer System

NOTE:

There are two types of customization procedures; one using the M-MDS and the other using the audio unit screen.

Auto wiper system

Personalization features

Setting contents

Setting procedure

Auto wiper system can be set to operable or inoperable.

Not Adopted./Off (Intermittent)/On (Rain Sensing)

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On (Rain Sensing)/

Off (Intermittent)

Audio unit screen is used for the setting.

(See AUDIO UNIT PERSONALIZATION FEATURES SETTING PROCEDURE.)

Instrumentation/Driver Info.

NOTE:

There are two types of personalization procedures; one using the M-MDS and the other using the instrument cluster.

Instrument cluster


Personalization features	Setting contents	Setting procedure
The volume for the lights-on reminder warning alarm can be changed.	Not Adopted./OFF/Low/High	M-MDS is used. (See INSTRUMENTATION/DRIVER INFO. PERSONALIZATION FEATURES SETTING PROCEDURE.)
	High / Low / OFF	Instrument cluster (with TFT LCD) is used. (See INSTRUMENTATION/DRIVER INFO. PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the turn and hazard indicator alarm can be changed.	Not Adopted./Low/High	M-MDS is used. (See INSTRUMENTATION/DRIVER INFO. PERSONALIZATION FEATURES SETTING PROCEDURE.)
	High / Low	Instrument cluster (with TFT LCD) is used. (See INSTRUMENTATION/DRIVER INFO. PERSONALIZATION FEATURES SETTING PROCEDURE.)
The display language can be changed.		Instrument cluster (with TFT LCD) is used. (See INSTRUMENTATION/DRIVER INFO. PERSONALIZATION FEATURES SETTING PROCEDURE.)
The distance unit can be changed.	km / miles	Instrument cluster (with TFT LCD) is used. (See INSTRUMENTATION/DRIVER INFO. PERSONALIZATION FEATURES SETTING PROCEDURE.)
The temperature unit can be changed.	°C / °F	Instrument cluster is used. (See INSTRUMENTATION/DRIVER INFO. PERSONALIZATION FEATURES SETTING PROCEDURE.)
The sound volume for the following operations can be changed. Trip computer data is reset INFO switch is pressed for 1.5 s or more while average fuel economy/average vehicle speed is displayed. Scrolling value is operated Up/down switch on period setting screen of maintenance monitor is pressed for 1.5 s or more.	High / Low / OFF	Instrument cluster (with TFT LCD) is used. (See INSTRUMENTATION/DRIVER INFO. PERSONALIZATION FEATURES SETTING PROCEDURE.)

Blind Spot Monitoring (BSM) System

NOTE:

There are two types of personalization procedures; one using the M-MDS and the other using the instrument cluster.

Personalization features

Setting contents

Setting procedure

The volume of the blind spot monitoring (BSM) warning alarm can be changed.

Not Adopted./OFF/Low/High

M-MDS is used.

(See INSTRUMENTATION/DRIVER INFO. PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / OFF

Instrument cluster (with TFT LCD) is used.

(See INSTRUMENTATION/DRIVER INFO. PERSONALIZATION FEATURES SETTING PROCEDURE.)

Smart City Brake Support (SCBS) (Instrument Cluster (with TFT LCD) Only)


Personalization features	Setting contents	Setting procedure
The operation of smart city brake support (SCBS) can be turned off.	ON / OFF	(See INSTRUMENTATION/DRIVER INFO. PERSONALIZATION FEATURES SETTING PROCEDURE.)

Jacking Positions, Vehicle Lift (2 Supports) And Safety Stand (Rigid Rack) Positions

Jacking Positions WARNING: Improperly jacking a vehicle is dangerous. The vehicle can slip off the jack and cause serious injury. Use only the correct front and rear jacking points and ...

Pre Delivery Inspection

Pre?Delivery Inspection Table Exterior INSPECT and ADJUST, if necessary, the following items to specification: ?Glass, exterior bright metal and paint for damage ?Wheel lug nuts ?All weathe ...

Other materials:

Engine Mount
Purpose, Function The engine mount secures the engine and transaxle to the vehicle body, reducing vibration and noise. Construction The three points at the engine front (No.3 engine mount), one side of the transaxle (No.1 engine mount), and the rear upper part of the transa ...

Cooling System
Outline Passing water resistance is reduced by improvement of the engine coolant passage shape. Pump efficiency is improved by changing the water pump impeller to the closed impeller. Structural View Flow Chart Structure Consists of the followi ...

Clock Spring Adjustment [Standard Deployment Control System]
1. Set the front wheels straight ahead. CAUTION: The clock spring will break if over?wound. Do not forcibly turn the clock spring. 2. Turn the clock spring clockwise until it stops. 3. Turn the clock spring counterclockwise approx. 2 turns. 4. Align the mark on the clo ...