Mazda CX-5 Service & Repair Manual: Wheel Hub Component Removal/Installation [Awd]
CAUTION:
-
Performing the following procedures without first removing the ABS wheel-speed sensor may possibly cause an open circuit in the wiring harness if it is pulled by mistake. Before performing the following procedures, disconnect the ABS wheel-speed sensor connector (body side) and fix the wiring harness to an appropriate place where it will not be pulled by mistake while servicing the vehicle.
1. When working on the left side of the vehicle, disconnect the auto leveling sensor link. .
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
4. Inspect the rear wheel alignment..
|
1 |
Locknut (See Locknut Installation Note.) |
|
2 |
ABS wheel-speed sensor |
|
3 |
Brake hose clip |
|
4 |
Brake caliper component |
|
5 |
Disc plate |
|
6 |
Bolt (wheel hub) (See WHEEL HUB COMPONENT REMOVAL/INSTALLATION [2WD].) |
|
7 |
Wheel hub |
|
8 |
Dust cover |
|
9 |
Rear stabilizer control link lower side nut |
|
10 |
Rear lower arm outer bolt (See WHEEL HUB COMPONENT REMOVAL/INSTALLATION [2WD].) |
|
11 |
Rear coil spring (See REAR COIL SPRING REMOVAL/INSTALLATION.) |
|
12 |
Rear shock absorber lower bolt (See REAR SHOCK ABSORBER REMOVAL/INSTALLATION.) |
|
13 |
Rear lateral link outer bolt (See REAR LATERAL LINK REMOVAL/INSTALLATION.) |
|
14 |
Rear trailing link installation bolt (See REAR LATERAL LINK REMOVAL/INSTALLATION.) |
|
15 |
Bolt (rear upper arm outer side) |
|
16 |
Hub support |
|
17 |
Wheel hub bolt (See WHEEL HUB COMPONENT REMOVAL/INSTALLATION [2WD].) |
|
18 |
Hub support bushing (front) (See WHEEL HUB COMPONENT REMOVAL/INSTALLATION [2WD].) |
|
19 |
Hub support bushing (rear) (See WHEEL HUB COMPONENT REMOVAL/INSTALLATION [2WD].) |
Locknut Installation Note
1. After tightening the locknut once at a torque of 390 N·m {40 kgf·m, 288 ft·lbf}
, return it temporarily 180 degrees
, then retighten it to a torque of 236—274 N·m {25—27 kgf·m, 175—202 ft·lbf}
.
Wheel Hub Component Removal/Installation [2 Wd]
CAUTION:
Performing the following procedures without first removing the ABS wheel-speed
sensor may possibly cause an open circuit in the wiring harness if it is pulled
by mistake. Befo ...
Front Suspension
...
Other materials:
Check Fuel Cap Warning Light
Purpose/Function
The check fuel cap warning light is built into the instrument cluster.
If the PCM detects that the fuel cap is open, the light illuminates to warn
the driver that the fuel cap is open.
Construction
Built into the instrument cluster.(See INSTRUMENT CLUS ...
Parking Brake Lever Removal/Installation
1. Remove the front console box..
2. Remove the shift lever knob. (MTX).
3. Remove the shift panel..
4. Remove the upper panel..
5. Remove in the order indicated in the table.
6. Install in the reverse order of removal.
7. After installation, inspect the parking brake lever stroke..
...
Quick Release Connector Removal/Installation
WARNING:
Fuel is very flammable liquid. If fuel spills or leaks from the pressurized
fuel system, it will cause serious injury or death and facility breakage. Fuel
can also irritate skin and eyes. To prevent this, always complete the “Fuel
Line Safety Procedure”, while referring ...
