WARNING:
Handling a side air bag improperly can accidentally operate (deploy) the air bag, which may seriously injure you. Read the service warnings/cautions in the Workshop Manual before handling the front seat (side air bag integrated)..
If the sliding mechanisms on both sides are not locked after assembling the front seat, the front seat will operate accidentally while the vehicle is driven, which could result in serious injury. After assembling the front seat, shake it up and down and verify that the sliding mechanism on the both sides are locked.
CAUTION:
If the slide bar is operated after the front seat is removed, the left/right slide positions will deviate and the adjuster unit could be damaged after the front seat is installed. After removing a front seat, do not operate the slider lever.
Verify that there are no malfunctions in the forward/back slide of the seat and in the adjuster unit after installing a front seat.
When performing the procedure with a front seat removed from the vehicle, perform the procedure on a clean cloth so as not to damage or soil the seat.
When the passenger's seat is removed, perform the seat weight sensor inspection using the M-MDS after installing the passenger's seat..
When the passenger's seat is replaced with a new one, perform the seat weight sensor calibration using the M-MDS..
Driver-side (with power seat system)
1. Switch the ignition off (LOCK).
2. Disconnect the negative battery cable and wait for 1 min
..
3. Remove the front seat..
4. Remove the front seat side cover..
5. Remove fasteners A and set the front seat cushion trim aside.
6. Disconnect the side air bag module connector.
7. Disengage clip B.
8. Disconnect the front seat back warmer connector.
9. Disconnect the recliner motor connector. (with 6 way power seat)
10. Disconnect the recliner motor/lumber support motor connector. (with 8 way power seat)
11. Set hooks C aside in the direction of the arrow (1) shown in the figure.
12. Remove the bolts A, then remove the front seat back component.
13. Install in the reverse order of removal.
Driver-side (without power seat system)
1. Switch the ignition off (LOCK).
2. Disconnect the negative battery cable and wait for 1 min
..
3. Remove the front seat..
4. Remove the front seat side cover..
5. Slide hook A in the order of arrows (1), (2), (3) shown in the figure and set the front seat cushion trim aside.
6. Disconnect the side air bag module connector.
7. Disengage clip B.
8. Set hooks C aside in the direction of the arrow (4) shown in the figure.
9. Remove the bolts A, then remove the front seat back component.
10. Install in the reverse order of removal.
Passenger-side
1. Switch the ignition off (LOCK).
2. Disconnect the negative battery cable and wait for 1 min
..
3. Remove the front seat..
4. Remove the front seat side cover..
5. Slide hook A in the order of arrows (1), (2), (3) shown in the figure and set the front seat cushion trim aside.
6. Disconnect the side air bag module connector.
7. Disconnect the front seat back warmer connector. (with seat warmer system)
8. Disengage clip B.
9. Set hook C aside in the direction of the arrow (4) shown in the figure.
10. Remove the bolts A, then remove the front seat back component.
11. Install in the reverse order of removal.
Starter Interlock Switch [Skyactiv G 2.0]
Purpose, Function
The starter interlock switch mechanism prevents vehicle surge when the engine
is started, enhancing safety. The engine cannot be started unless the clutch
is depressed.
Construction
The mechanism is provided with a starter interlock switch on the circuit
...
Windshield Washer Nozzle Adjustment
CAUTION:
If the nozzle is adjusted by inserting a stick-like object into the nozzle,
it could deform the injection nozzle and the washer fluid may not spray normally.
When adjusting the nozzle, do not insert objects into the injection nozzle.
1. Insert a tape-wrapped precision fl ...
Pressure Control Valve [Skyactiv G 2.0]
U.S.A. And CANADA
Purpose, function
Prevents fuel tank damage by suppressing the vacuum applied to the fuel tank
while the purge solenoid valve is open.
Suppresses the vacuum applied from the charcoal canister side to the fuel
tank.
Construction
Integrated with the ...