Mazda CX-5 Service & Repair Manual: Evaporative Emission (Evap) Control System
Purpose, Outline
-
Prevents release of evaporative gas into the atmosphere.
-
The intake manifold vacuum introduces evaporative gas to the intake manifold via the charcoal canister and the purge solenoid valve.
System Diagram
U.S.A. and CANADA
Except U.S.A. and CANADA
Structure
-
The evaporative emission control system consists of the following parts:
|
Part name |
Reference |
|
Purge solenoid valve |
(See PURGE SOLENOID VALVE [SKYACTIV-G 2.0].) |
|
Catch tank |
(See CATCH TANK [SKYACTIV-G 2.0].) |
|
Charcoal canister |
(See CHARCOAL CANISTER [SKYACTIV-G 2.0].) |
|
Pressure control valve |
(See PRESSURE CONTROL VALVE [SKYACTIV-G 2.0].) |
|
Fuel shut-off valve |
(See FUEL SHUT-OFF VALVE [SKYACTIV-G 2.0].) |
|
Rollover valve |
(See ROLLOVER VALVE [SKYACTIV-G 2.0].) |
|
Fuel-filler cap |
(See FUEL-FILLER CAP [SKYACTIV-G 2.0].) |
|
CV solenoid valve |
(See CANISTER VENT (CV) SOLENOID VALVE [SKYACTIV-G 2.0].) |
Except U.S.A. and CANADA
|
Part name |
Reference |
|
Purge solenoid valve |
(See PURGE SOLENOID VALVE [SKYACTIV-G 2.0].) |
|
Catch tank |
(See CATCH TANK [SKYACTIV-G 2.0].) |
|
Charcoal canister |
(See CHARCOAL CANISTER [SKYACTIV-G 2.0].) |
|
Check valve |
(See CHECK VALVE [SKYACTIV-G 2.0].) |
|
Rollover valve |
(See ROLLOVER VALVE [SKYACTIV-G 2.0].) |
|
Fuel-filler cap |
(See FUEL-FILLER CAP [SKYACTIV-G 2.0].) |
Emission System
Purpose, Outline
A single-nano catalyst has been adopted for the under-floor, three-way catalyst
to improve emission gas purification efficiency.
Structural View
Engine compartment si ...
Exhaust Gas Purification System
Purpose, Outline
Purifies contaminants (HC, CO, NOx) in the exhaust gas by utilizing the chemical
reactions of the three-way catalytic converter.
System Diagram
Structure
T ...
Other materials:
Washer Tank Removal/Installation
With Washer Fluid-level Sensor
1. Disconnect the negative battery cable..
2. Set the front over fender aside..
3. Set the mudguard (RH) aside..
4. Remove the front bumper..
5. Remove the bracket.
6. Disconnect the washer motor connector.
7. Disconnect the washer fluid-level sensor c ...
Refrigerant Pressure Sensor Inspection [Manual Air Conditioner]
1. Install the manifold gauge.
2. Verify the high-pressure side reading of the manifold gauge.
3. Measure the terminal voltage at PCM terminals 2BB, 2AX and 2AJ
4. Using the graph below, measure and verify the terminal voltage at 2AX.
5. Follow the PCM inspection when measuring the other ter ...
Auxiliary Jack/Usb Port
NOTE:
“iPod” is a registered trademark of Apple Inc. in the United States and other
countries.
Purpose, Function
The Auxiliary jack/USB port outputs the audio signals of commercially-available
portable audio, a USB device, or an iPod connected to the Auxiliary jack/USB ...
