Mazda CX-5 Service & Repair Manual: Control System Personalization Features Setting Procedure
1. Connect the M-MDS to DLC-2.
2. After the vehicle is identified, select the following items from the initial screen of the M-MDS.
-
Select the “Module Programming”.
-
Select “Programmable Parameters”.
-
Select menu in the R_BCM.
3. Select an item name, and then select option.
Security And Locks
Power door lock system
|
M-MDS display |
Function |
Initial setting |
Setting contents |
Control unit |
|
Auto Door Lock Mode. |
Auto door lock function can be changed. |
Lock: Driving, Unlock: IGN Off. |
Not Adopted./OFF/Lock When Driving./Lock: Driving, Unlock: IGN Off./Lock When Shifting Out Of P./Lock: Shift From P, Unlock: In P. |
Rear body control module (RBCM) |
Lighting Systems
Turn light system
|
M-MDS display |
Function |
Initial setting |
Setting contents |
Control unit |
|
3-Flash Turn Signal. |
The turn light system can be switched between operable and inoperable. |
OFF |
Not Adopted./OFF/ON |
Rear body control module (RBCM) |
Auto light system
|
M-MDS display |
Function |
Initial setting |
Setting contents |
Control unit |
|
Auto-headlight On. |
Auto light sensor sensitivity can be changed. |
Medium |
Not Adopted./Dark/Medium Dark/Medium/Medium Light/Light |
Rear body control module (RBCM) |
Auto light-off system
|
M-MDS display |
Function |
Initial setting |
Setting contents |
Control unit |
|
Headlight Off Timer. |
The headlight emitted time of the auto light off timer can be changed. |
30 seconds. |
Not Adopted./0 seconds./30 seconds./60 seconds./90 seconds./120 seconds. |
Rear body control module (RBCM) |
Room Light Control System
|
M-MDS display |
Function |
Initial setting |
Setting contents |
Control unit |
|
Interior Light Timeout-Door Open. |
The front/rear map light illumination time after any door is open can be changed. |
30 minutes. |
Not Adopted./30 minutes./60 minutes./10 minutes. |
Rear body control module (RBCM) |
|
Interior Light Timeout-Door Closed. |
The front/rear map light illumination time after any door is open can be changed. |
15 seconds. |
Not Adopted./15 seconds./7.5 seconds./30 seconds./60 seconds. |
Rear body control module (RBCM) |
Wiper/washer System
Auto wiper system
|
M-MDS display |
Function |
Initial setting |
Setting contents |
Control unit |
|
Rain Sensing Wipers. |
Auto wiper system can be set to operable or inoperable. |
Lock: Driving, Unlock: IGN Off. |
Not Adopted./Off (Intermittent)/On (Rein Sensing) |
Rear body control module (RBCM) |
Clock Spring Removal/Installation [Standard Deployment Control System]
CAUTION:
If the disc on the combination switch is deformed or has foreign material
adhering to it, performance of the steering angle sensor may be reduced, causing
abnormal operation. Wh ...
Control System [Full Auto Air Conditioner]
Outline
Refrigerant pressure sensor adopted in which refrigerant pressure is changed
into a linear electric signal and precise information is transmitted.
MS-CAN for communicatio ...
Other materials:
Rear Seat Center Armrest Removal/Installation
1. Operate the push knob (RH) and lower the rear seat back (RH).
2. Remove screw A.
3. Remove the rear seat center armrest hinge cover (RH) in the direction of the
arrow (1) shown in the figure while setting hook A aside.
4. Remove bolt B.
5. Remove the rear seat center armrest in ...
Side Turn Light Inspection
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Outer mirror glass.
b. Upper outer mirror garnish.
c. Side turn light.
3. Apply battery voltage to side turn light terminal A, and connect terminal
B to ground.
4. Verify that the LED illuminates.
...
Liftgate Removal/Installation
WARNING:
Removing the stay damper, liftgate hinge securing bolt, or liftgate without
supporting the liftgate may cause the liftgate to fall off and injure you. When
removing the stay damper, liftgate hinge, or liftgate, always use two persons
to perform the work.
1. Disconnect ...
