Mazda CX-5 Service & Repair Manual: Plastic Parts Heat Resisting Temperature [Plastic Body Parts]
|
Part Name |
Code |
Material Name |
Heat resisting Temperature°C{°F} |
|||
|
Windshield molding |
PVC |
POLYVINYLCHLORIDE |
95 {203} |
|||
|
Cowl grille |
PP |
POLYPROPYLENE |
95 {203} |
|||
|
Front combination light |
Lens |
PC |
POLYCARBONATE |
130 {266} |
||
|
Housing |
PP |
POLYPROPYLENE |
90 {194} |
|||
|
Front bumper |
PP |
POLYPROPYLENE |
100 {212} |
|||
|
Front side turn light |
Lens |
PMMA |
ACRYLIC |
75 {167} |
||
|
Housing |
PC-PBT |
POLYCARBONATE-PBT |
80 {176} |
|||
|
Out side mirror |
Panel |
ABS |
ABS |
100 {212} |
||
|
Visor |
ABS |
ABS |
100 {212} |
|||
|
Outer cover |
ABS |
ABS |
100 {212} |
|||
|
Side step molding |
PP |
POLYPROPYLENE |
75 {167} |
|||
|
Roof molding |
PVC |
POLYVINYLCHLORIDE |
95 {203} |
|||
|
Rear bumper |
PP |
POLYPROPYLENE |
100 {212} |
|||
|
Rear combination light |
Lens |
PMMA |
ACRYLIC |
80 {176} |
||
|
Housing |
AAS |
AAS |
70 {158} |
|||
|
Outer handle |
Lever |
PC-PBT |
POLYCARBONATE-PBT |
80 {176} |
||
|
Base |
PC-PET |
POLYCARBONATE-PET |
80 {176} |
|||
|
High-mount brake light |
Lens |
PMMA |
ACRYLIC |
80 {176} |
||
|
Housing |
ABS |
ABS |
100 {212} |
|||
|
Rear Spoiler |
PP |
POLYPROPYLENE |
90 {194} |
|||
|
Shroud panel |
PP |
POLYPROPYLENE |
100 {212} |
|||
NOTE:
-
The application of temperatures higher than heat resisting temperatures may result in part deformation.
Lower Panel Removal/Installation
Driver-side
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Driver-side front scuff plate.
b. Driver-side front side trim.
c. Switch panel.
d. Decoration panel. ...
Other materials:
Hood Removal/Installation
WARNING:
Removing the hood without supporting it could cause the hood to fall and
cause serious injury. Always perform the procedure with at least another person
to prevent the hood from falling.
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Fro ...
Liftgate Latch Switch Inspection
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Liftgate upper trim.
b. Liftgate side trim.
c. Liftgate lower trim.
d. Liftgate latch and lock actuator.
3. Verify that the continuity is as indicated in the table.
If not as indicated in the tab ...
Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Standard Deployment
Control System]
WARNING:
A live (undeployed) air bag module or pre-tensioner seat belt may accidentally
operate (deploy) when it is disposed of and cause serious injury. Do not dispose
of a live (undeployed) air bag module or pre-tensioner seat belt. If the SSTs
(Deployment tool and Adapter harness ...
