Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Rear Crossmember Removal/Installation [Awd]

Mazda CX-5 Service & Repair Manual / Drivetrain / Driveline / 4WD / Rear Crossmember Removal/Installation [Awd]

WARNING:

  1. Verify that the crossmember is securely supported by a jack. If the rear crossmember falls off, it can cause serious injury or death, and damage to the vehicle.

CAUTION:

NOTE:

1. Disconnect the wiring harness clips and connectors installed to the rear crossmember.


2. Set the rear differential breather hose aside.


3. Remove the auto leveling sensor. (With auto leveling sensor).


4. Disconnect the rear ABS wheel-speed sensor wiring harness installed to rear hub support, then move aside the rear ABS sensor..


5. Jack up the vehicle to the unloaded condition, and support the rear trailing link component using a jack.


6. Align the rear crossmember component and rear upper arm and mark them.


7. Remove the propeller shaft..

8. Remove the TWC..

9. Remove the rear lateral link..

10. Remove the rear coil spring..

11. Remove the rear lower arm..

12. Remove the rear drive shaft..

13. Remove in the order indicated in the table.

14. Install in the reverse order of removal.

15. Inspect the wheel alignment and adjust it if necessary..



1

Rear crossmember component

(See Rear Crossmember Component Removal Note.)

(See Rear Crossmember Component Installation Note.)

2

Rear stabilizer component

3

Rear upper arm

.

4

Rear crossmember mudguard

5

Front differential mounting rubber

(See REAR DIFFERENTIAL REMOVAL/INSTALLATION.)

6

Rear differential component

(See REAR DIFFERENTIAL REMOVAL/INSTALLATION.)

7

Rear crossmember


Rear Crossmember Component Removal Note

WARNING:

  1. Verify that the rear crossmember is securely supported by a jack. If the rear crossmember falls off, it can cause serious injury or death, and damage to the vehicle.

1. Support the rear crossmember component with the jack and remove the nut.


2. Remove the rear crossmember component.

Rear Crossmember Component Installation Note

WARNING:

  1. Verify that the rear crossmember is securely supported by a jack. If the rear crossmember falls off, it can cause serious injury or death, and damage to the vehicle.

1. Support the rear crossmember component and install the rear crossmember.


Rear ABS Wheel Speed Sensor Inspection [Awd]
Installation Visual Inspection 1. Inspect the following items: If there is any malfunction, replace the applicable part. a. Excessive play of the ABS wheel-speed sensor b. Deformation ...

Rear Stabilizer Removal/Installation [Awd]
WARNING: Verify that the rear crossmember is securely supported by a jack. If the rear crossmember falls off, it can cause serious injury or death, and damage to the vehicle. CAUTI ...

Other materials:

When Warning/Indicator Lights Illuminate/Flash
If the brake system warning light illuminates If the light stays on after the parking brake is fully released there may be a problem with the brakes. Drive to the side of the road and park off the right-of-way. You may notice that the pedal is harder to depress or that it may go closer to t ...

Automatic Transaxle Removal/Installation [Fw6 A EL]
CAUTION: Performing the following procedures without first removing the front ABS wheel-speed sensor may possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the following procedures, disconnect the front ABS wheel-speed sensor (axle side) and ...

Fuel Filter (High Pressure) Removal/Installation
WARNING: Fuel is very flammable liquid. If fuel spills or leaks from the pressurized fuel system, it will cause serious injury or death and facility breakage. Fuel can also irritate skin and eyes. To prevent this, always complete the “Fuel Line Safety Procedure”, while referring ...

© 2016-2026 Copyright www.mcx5.org