Mazda CX-5 Service & Repair Manual: Antenna Feeder No.3 Removal/Installation

Mazda CX-5 Service & Repair Manual / Accessories / Electronics / Entertainment / Antenna Feeder No.3 Removal/Installation

1. Disconnect the negative battery cable..

2. Remove the following parts:

a. B-pillar lower trim.

b. Front seat belt adjusting cover.

c. Front seat belt upper anchor installation bolt.

d. B-pillar upper trim.

e. Trunk board.

f. Trunk end trim.

g. Trunk side trim.

h. D-pillar trim.

i. C-pillar trim.

j. Liftgate upper trim (with SIRIUS satellite radio system).

3. Remove the rear passenger's assist handle..

4. Partially peel back the headliner.

NOTE:

If the headliner is peeled back excessively, the headliner could become creased. Be careful not to peel back the headliner excessively.

5. Disconnect antenna feeder No.2.

6. Remove the bolt.

7. Remove clips A and B.

8. Remove joint pipe No.1 clip.

9. Remove clips D and E.

10. Disconnect joint pipe No.2.

11. Remove clips F and G.

12. Disconnect the center roof antenna.

13. Using a screwdriver wrapped in protective tape, pull the connector in the direction of the arrow (2) shown in the figure while pressing glass antenna terminal in the direction of the arrow (1) shown in the figure, and disengage the glass antenna terminal from the connector. (with SIRIUS satellite radio system)

14. Disconnect the connector. (with SIRIUS satellite radio system)

15. Remove the bolt. (with SIRIUS satellite radio system)

16. Remove the clip. (with SIRIUS satellite radio system)

17. Partially peel the liftgate grommet in the direction of arrow (1) shown in the figure, and remove the liftgate grommet from the liftgate grommet inner. (with SIRIUS satellite radio system)

18. Using a screwdriver wrapped in protective tape, pull the liftgate grommet in the direction of the arrow (2) shown in the figure while pressing the liftgate grommet inner tab in the direction of the arrow (1) shown in the figure, and disengage the liftgate from the liftgate grommet. (with SIRIUS satellite radio system)

19. Pull the liftgate grommet in the direction of the arrow (1) shown in the figure and remove it.

20. Pull out the disconnected connectors of the liftgate side and vehicle interior side and antenna feeder No.3. (with SIRIUS satellite radio system)

21. Remove antenna feeder No.3.

22. Install in the reverse order of removal.

Antenna Feeder No.3 Inspection

1. Disconnect the negative battery cable.. 2. Remove the following parts: a. Front scuff plate. b. Rear scuff plate. c. B-pillar lower trim. d. Front seat belt adjusting cover. e. Front se ...

Audio Amplifier

Purpose, Function The audio signal (analog voltage waveform) output from the unit equipped on the vehicle is converted into a digital pulse. The converted digital pulse signal is amplifie ...

Other materials:

Clock Spring Inspection [Standard Deployment Control System]
1. Disconnect the negative battery cable and wait for 1 min or more.. 2. Remove the driver?side air bag module.. 3. Remove the steering wheel.. 4. Remove the column cover.. 5. Remove the clock spring.. 6. Verify that the continuity is as indicated in the table. If not as indicated ...

Refrigerant Pressure Check
NOTE: Measure the refrigerant pressure after approx.10 min have elapsed from engine start. 1. Install the manifold gauge.. 2. Start the engine and warm it up. 3. Set the fan speed MAX HI. 4. Turn the A/C switch on. 5. Set to RECIRCULATE mode. 6. Set the temperature control ...

Air Bag System Warning Light [Two Step Deployment Control System]
Purpose The air bag system warning light notifies the driver of a malfunction in the SRS air bag system. Function If a malfunction occurs in the SRS air bag system, the air bag system warning light illuminates or flashes. Construction LEDs (light-emitting d ...