Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Windshield Wiper System

Outline

Structural View


System Wiring Diagram


Operation

Continuous low operation

1. When the wiper and washer switch is moved to the LO position with the ignition switched ON (engine off or on) (1), the start stop unit detects a windshield wiper switch signal (LO).(2)

2. When the start stop unit detects the windshield wiper switch signal (LO), it send a windshield wiper switch position signal (LO) to the front body control module (FBCM) as a CAN signal.(3)

3. When the front body control module (FBCM) receives the windshield wiper switch position signal (LO), it supplies the base current from the internal CPU to transistor A (4), and collector current flows from the internal power supply (5), turning the windshield wiper low relay on. (6)

4. When the windshield wiper low relay is turned on, current flows from the battery to the windshield wiper motor and the windshield wipers operate continuously at low speed.(7)


Continuous high operation

1. When the wiper and washer switch is moved to the HI position with the ignition switched ON (engine off or on) (1), the start stop unit detects a windshield wiper switch signal (HI).(2)

2. When the start stop unit detects a windshield wiper switch signal (HI), it send a windshield wiper switch position signal (HI) to the front body control module (FBCM) as a CAN signal.(3)

3. When the front body control module (FBCM) receives the windshield wiper switch position signal (HI), it supplies the base current from the internal CPU to transistors A and B (4), and collector current flows from the internal power supply (5), turning the windshield wiper low relay and windshield wiper high relay on.(6)

4. When the windshield wiper low relay and windshield wiper high relay are turned on, current flows from the battery to the windshield wiper motor and the windshield wipers operate continuously at high speed.(7)


Auto-stop operation

1. During intermittent operation, or when the wiper and washer switch is moved to the OFF position (1), the auto stop switch inside the windshield wiper motor turns on when the windshield wipers move to the park position.(2)

2. When the front body control module (FBCM) detects that the auto stop switch is on, it stops the base current to the transistor (3) and turns off the windshield wiper low relay, and the windshield wipers stop at the park position.


One-touch wiper operation

1. When the wiper and washer switch is moved up with the ignition switched ON (engine off or on) (1), the start stop unit detects a windshield wiper switch signal (LO).(2)

2. When the start stop unit detects a windshield wiper switch signal (LO), it send a windshield wiper switch position signal (LO) to the front body control module (FBCM) as a CAN signal.(3)

3. When the front body control module (FBCM) receives the windshield wiper switch position signal (LO), it supplies the base current from the internal CPU to transistor A (4), and collector current flows from the internal power supply (5), turning the windshield wiper low relay on.(6)

4. When the windshield wiper low relay is turned on, current flows from the battery to the windshield wiper motor and the windshield wipers operate at low speed.(7)


Intermittent wiper operation (without auto wiper system)

1. When the wiper and washer switch is moved to the INT position with the ignition switched ON (engine off or on) (1), the start stop unit detects a windshield wiper switch signal (INT).(2)

2. When the start stop unit detects a windshield wiper switch signal (INT), it send a windshield wiper switch position signal (INT) and an INT volume signal to the front body control module (FBCM) as CAN signals.(3)

3. When the front body control module (FBCM) receives the windshield wiper switch position signal (INT), it supplies the base current from the internal CPU to transistor A (4), and collector current flows from the internal power supply (5), turning the windshield wiper low relay on.(6)

4. When the windshield wiper low relay is turned on, current flows from the battery to the windshield wiper motor and the windshield wipers operate continuously at low speed.(7)

5. The windshield wipers stop at the park position due to the auto stop operation, and after a certain period of time has elapsed, which was calculated based on the INT volume signal, the front body control module (FBCM) operates the windshield wipers at a low speed. By repeating this, the windshield wipers operate intermittently.(8)


Auto wiper operation (with auto wiper system)

Synchronized washer and wiper operation

1. When the windshield washer switch is turned on with the ignition switched ON (engine off or on) and the windshield wipers not operated (1), the start stop unit detects a windshield washer switch ON signal.(2)

2. When the start stop unit detects a windshield washer switch ON signal, it send a windshield washer operation request signal to the front body control module (FBCM) as a CAN signal.(3)

3. When the front body control module (FBCM) receives the windshield washer operation request signal, it supplies the base current from the internal CPU to transistor C (4), and collector current flows from the internal power supply (5), turning the windshield washer relay on.(6)

4. When the windshield washer relay is turned on, current flows from the power supply inside the front body control module (FBCM) to the washer motor and the washer motor operates, and washer fluid is sprayed from the front washer nozzles.(7)

5. When the front body control module (FBCM) receives the windshield washer operation request signal for a certain period of time, it operates the windshield wipers at low speed.(8)

6. When the windshield washer switch is turned off, the operation stops after the windshield wipers operate two times.

NOTE:


LO/HI detection function

Windshield Wiper Motor Inspection
1. Disconnect the negative battery cable.. 2. Remove the following parts: a. Windshield wiper arm and blade. b. Cowl grille. Windshield Wiper Motor Inspection 1. Apply battery positive voltag ...

Wiper Bracket Removal [Panel Replacement]
Symbol Mark Installation Procedure 1. When installing new parts, measure and adjust the body as necessary to conform with standard dimensions. 2. Drill holes for the plug welding before inst ...

Other materials:

Caliper (Front) Disassembly/Assembly
1. Disassemble in the order indicated in the table. 1 Bleeder cap 2 Bleeder screw 3 Piston (See Piston Disassembly Note.) 4 Dust seal 5 Piston seal ...

Battery Recharging [Skyactiv G 2.0]
Using GR8-1291: (See GR8-1291 INSTANT TRAINING MODULE (VIDEO).) WARNING: Keep all flames away from the battery, otherwise evaporated gas from the battery fluid may catch fire and cause serious injury. 1. Remove the battery filler caps and check the water level. If necessary, add ...

Cargo Compartment Light
Purpose The cargo compartment light illuminates the cargo room interior when the liftgate is opened. Function When the liftgate is opened, illuminates by the cargo room light switch turning on. Construction The cargo room light is installed to the trunk side tr ...

© 2016-2024 Copyright www.mcx5.org