Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Wheel Hub, Steering Knuckle Removal/Installation

Mazda CX-5 Service & Repair Manual / Suspension / Front Suspension / Wheel Hub, Steering Knuckle Removal/Installation

CAUTION:

1. Disconnect the front ABS wheel-speed sensor..

2. Remove in the order indicated in the table.

3. Install in the reverse order of removal.

4. After installation, inspect the front wheel alignment and adjust it if necessary..



1

ABS wheel-speed sensor

2

Brake hose clip

3

Locknut

(See Locknut Removal Note.)

(See Locknut Installation Note.)

4

Brake caliper component

(See Brake Caliper Removal Note.)

5

Disc plate

6

Stabilizer control link (upper side)

7

Tie-rod end ball joint

.

8

Front lower arm ball joint

9

Front shock absorber bolt

(See Front Shock Absorber Bolt Installation Note.)

10

Bolt (wheel hub)

(See Bolt (Wheel Hub) Installation Note.)

11

Wheel hub

(See Wheel Hub Installation Note.)

12

Dust cover

13

Steering knuckle

14

Wheel hub bolt

(See Wheel Hub Bolt Removal Note.)

(See Wheel Hub Bolt Installation Note.)


Locknut Removal Note

1. Remove the locknut.

2. Install a spare nut onto the drive shaft so that the nut is flush with the end of the drive shaft.

3. Tap the nut with a copper hammer to loosen the drive shaft from the front wheel hub.


4. Separate the drive shaft from the wheel hub.

Brake Caliper Removal Note

1. Remove the brake caliper component from the steering knuckle and suspend it out of the way using a cable.


Wheel Hub Bolt Removal Note

NOTE:

1. Remove the wheel hub bolt using a press.


Wheel Hub Bolt Installation Note

1. Install the new wheel hub bolt using a press.


Wheel Hub Installation Note

1. Apply grease (L2Y1 33247) to the wheel bearing inner race and drive shaft contact surface (Area A in figure).


Bolt (Wheel Hub) Installation Note

CAUTION:

Front Shock Absorber Bolt Installation Note

1. Install the steering knuckle to the front shock absorber, insert the bolts from the direction shown as follows, then tighten them to the specified torque.

Locknut Installation Note

1. After tightening the locknut once at a torque of 390 N·m {40 kgf·m, 288 ft·lbf}

, return it temporarily 180 degrees

, then retighten it to a torque of 236—274 N·m {25—27 kgf·m, 175—202 ft·lbf}

.

Wheel Hub, Steering Knuckle Inspection
Wheel Bearing Excessive Play Inspection 1. Install the magnetic base and dial gauge as shown in the figure and measure the wheel bearing axial excessive play. If it exceeds the maximu ...

Rear Suspension
...

Other materials:

DSC HU/CM Inspection
1. Disconnect the DSC HU/CM connector.. 2. Connect the negative battery cable.. 3. Attach the tester lead to the DSC HU/CM wiring harness-side connector and inspect voltage, continuity, or resistance according to the standard (reference) on the table. Standard (Reference) ...

Turbine/Input Shaft Speed Sensor, Output Shaft Speed Sensor [Fw6 A EL, Fw6 Ax EL]
Purpose/Function The turbine/input shaft speed sensor detects the rotation speed of the input shaft (low clutch drum). The output shaft speed sensor detects the rotation speed of the output shaft (primary gear). The turbine/input shaft speed sensor and output shaft speed ...

Outer Mirror Glass Removal
1. Disconnect the negative battery cable.. 2. Press area A of the outer mirror glass shown in the figure so that area B moves outward. 3. Put your hand on the lower part of the outer mirror glass and while supporting the hatch-marked area shown in the figure, remove pin C in the directio ...

© 2016-2025 Copyright www.mcx5.org