Mazda CX-5 Service & Repair Manual: Wheel Hub Component Removal/Installation [Awd]
CAUTION:
-
Performing the following procedures without first removing the ABS wheel-speed sensor may possibly cause an open circuit in the wiring harness if it is pulled by mistake. Before performing the following procedures, disconnect the ABS wheel-speed sensor connector (body side) and fix the wiring harness to an appropriate place where it will not be pulled by mistake while servicing the vehicle.
1. When working on the left side of the vehicle, disconnect the auto leveling sensor link. .
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
4. Inspect the rear wheel alignment..
|
1 |
Locknut (See Locknut Installation Note.) |
|
2 |
ABS wheel-speed sensor |
|
3 |
Brake hose clip |
|
4 |
Brake caliper component |
|
5 |
Disc plate |
|
6 |
Bolt (wheel hub) (See WHEEL HUB COMPONENT REMOVAL/INSTALLATION [2WD].) |
|
7 |
Wheel hub |
|
8 |
Dust cover |
|
9 |
Rear stabilizer control link lower side nut |
|
10 |
Rear lower arm outer bolt (See WHEEL HUB COMPONENT REMOVAL/INSTALLATION [2WD].) |
|
11 |
Rear coil spring (See REAR COIL SPRING REMOVAL/INSTALLATION.) |
|
12 |
Rear shock absorber lower bolt (See REAR SHOCK ABSORBER REMOVAL/INSTALLATION.) |
|
13 |
Rear lateral link outer bolt (See REAR LATERAL LINK REMOVAL/INSTALLATION.) |
|
14 |
Rear trailing link installation bolt (See REAR LATERAL LINK REMOVAL/INSTALLATION.) |
|
15 |
Bolt (rear upper arm outer side) |
|
16 |
Hub support |
|
17 |
Wheel hub bolt (See WHEEL HUB COMPONENT REMOVAL/INSTALLATION [2WD].) |
|
18 |
Hub support bushing (front) (See WHEEL HUB COMPONENT REMOVAL/INSTALLATION [2WD].) |
|
19 |
Hub support bushing (rear) (See WHEEL HUB COMPONENT REMOVAL/INSTALLATION [2WD].) |
Locknut Installation Note
1. After tightening the locknut once at a torque of 390 N·m {40 kgf·m, 288 ft·lbf}
, return it temporarily 180 degrees
, then retighten it to a torque of 236—274 N·m {25—27 kgf·m, 175—202 ft·lbf}
.
Turbine/Input Shaft Speed Sensor, Output Shaft Speed Sensor [Fw6 A EL, Fw6 Ax
EL]
Purpose/Function
The turbine/input shaft speed sensor detects the rotation speed of the input
shaft (low clutch drum).
The output shaft speed sensor detects the rotation speed of the ...
Differentials
...
Other materials:
St 001/12 Special Service Tool Shipment January 2013
APPLICABLE MODEL(S)/VINS
2014 Mazda6
2014 CX-5
DESCRIPTION/PRICING
In support of the new 2014 Mazda6 and the 2014 CX-5, Mazda will ship to all dealers
one (1) new Special Service Tool (SST). The SST will be shipped automatically by
Mazda’s tool vendor, SPX during January 2013.
The followi ...
Rear Wiper And Washer Switch Inspection
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Column cover.
b. Wiper and washer switch.
3. Use a tester to measure and verify that the continuity between the rear wiper
and washer switch terminals is as indicated in the table.
If the continuity is ...
Down Switch Inspection [Fw6 A EL, Fw6 Ax EL]
Continuity Inspection
NOTE:
The down switch is built into the selector lever component.
1. Disconnect the negative battery cable..
2. Remove the front console..
3. Disconnect the selector lever component connector.
4. Verify that the continuity between selector lever compone ...
