Mazda CX-5 Service & Repair Manual: Wheel Hub Component Removal/Installation [2 Wd]
CAUTION:
-
Performing the following procedures without first removing the ABS wheel-speed sensor may possibly cause an open circuit in the wiring harness if it is pulled by mistake. Before performing the following procedures, disconnect the ABS wheel-speed sensor connector (body side) and fix the wiring harness to an appropriate place where it will not be pulled by mistake while servicing the vehicle.
1. When working on the left side of the vehicle, disconnect the auto leveling sensor link. .
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
4. Inspect the rear wheel alignment..
|
1 |
ABS wheel-speed sensor |
|
2 |
Brake hose clip |
|
3 |
Brake caliper component . |
|
4 |
Disc plate |
|
5 |
Bolt (wheel hub) (See Bolt (Wheel Hub) Installation Note.) |
|
6 |
Wheel hub |
|
7 |
Dust cover |
|
8 |
Rear stabilizer control link lower side nut |
|
9 |
Rear lower arm outer bolt . |
|
10 |
Rear coil spring (See REAR COIL SPRING REMOVAL/INSTALLATION.) |
|
11 |
Rear shock absorber lower bolt (See REAR SHOCK ABSORBER REMOVAL/INSTALLATION.) |
|
12 |
Rear lateral link outer bolt (See REAR LATERAL LINK REMOVAL/INSTALLATION.) |
|
13 |
Rear trailing link installation bolt (See REAR LATERAL LINK REMOVAL/INSTALLATION.) |
|
14 |
Bolt (rear upper arm outer side) |
|
15 |
Hub support |
|
16 |
Wheel hub bolt . |
|
17 |
Hub support bushing (front) . |
|
18 |
Hub support bushing (rear) . |
Brake Caliper Component Removal Note
1. Remove the brake caliper component from the trailing link and suspend it out of the way using a cable.
Rear Lower Arm Outer Bolt Removal Note
1. Support the rear lower arm using a jack.
2. Remove the rear lower arm outer bolt.
Wheel Hub Bolt Removal Note
NOTE:
-
The wheel hub bolts do not need to be removed unless they are being replaced.
1. Remove the wheel hub bolt using a press.
Hub Support Bushing (Front) Removal Note
1. Mark the hub Support as shown in the figure.
2. Press the rear hub support bushing (front) out using the SSTs
.
Hub Support Bushing (Rear) Removal Note
1. Mark the hub Support as shown in the figure.
2. Press the rear hub support bushing (rear) out using the SSTs
.
Hub Support Bushing (Rear) Installation Note
1. Align the projection of a hub support bushing with the marks placed during removal.
2. Install a new hub support bushing (rear) using the SSTs
.
Hub Support Bushing (Front) Installation Note
1. Align the projection of a hub support bushing with the marks placed during removal.
2. Install a new hub support bushing (front) using the SSTs
.
Wheel Hub Bolt Installation Note
1. Install the new wheel hub bolt using a press.
Bolt (Wheel Hub) Installation Note
CAUTION:
-
The wheel hub installation bolts are tightened to a specific angle, but they are not plastic tightening bolts. Accordingly, the bolt length inspection is not needed.
Wheel Hub Component Inspection
Wheel Bearing Excessive Play Inspection
1. Install the magnetic base and dial gauge as shown in the figure and measure
the wheel bearing axial excessive play.
If it exceeds the maximu ...
Wheel Hub Component Removal/Installation [Awd]
CAUTION:
Performing the following procedures without first removing the ABS wheel-speed
sensor may possibly cause an open circuit in the wiring harness if it is pulled
by mistake. Befo ...
Other materials:
Corner Junction Installation [Panel Replacement]
Symbol Mark
Installation Procedure
1. When installing new parts, measure and adjust the body as necessary to conform
with standard dimensions.
2. Drill holes for the plug welding before installing the new parts.
3. After temporarily installing new parts, make sure the related parts fit p ...
Tire Pressure Monitoring System
Tire Pressure Monitoring System
• The Tire Pressure Monitoring System (TPMS)
monitors the air pressure of all four wheels. If the air pressure of one or more
tires is too low, the system warns the driver by indicating the tire pressure monitoring
system warning light in the instrument clust ...
Starting a Flooded Engine
If the engine fails to start, it may be flooded (excessive fuel in the engine).
Follow this procedure:
1. If the engine does not start within five seconds on the first try, wait ten
seconds and try again.
2. Make sure the parking brake is on.
3. Depress the accelerator all the way and hold it ...
