Mazda CX-5 Service & Repair Manual: Ultra High Tension Steel [Construction]
Characteristics of Ultra High-Tensile Steel Plates
-
Ultra high-tensile steel plates have enhanced tensile strength compared to previous high-tensile steel plates.
-
Because the strength is maintained even though the plates are thin-walled, the ultra high-tensile steel plates are used for the frames and the main frame parts which form the cabin, reducing the weight of the vehicle.
-
Enhanced shock absorption has improved the safety.
Range of Use and Cautions for Service
-
Because the ultra high-tensile steel is hard and it may be difficult to reform, when extracting the damaged part using a frame repair machine, perform the work verifying that other parts are not affected.
-
When drilling welded parts, use a well-ground drill bit.
-
After welding, inspect the weld strength. If adhesion is poor, perform arc welding (plug welding).
|
NO.
|
Part Name
|
Strength (MPa)
|
|
1 |
Bumper bracket |
590 |
|
2 |
Front side frame (outer, rear) |
590 |
|
3 |
Front side frame (inner, rear) |
590 |
|
4 |
Apron reinforcement No.3 |
590 |
|
5 |
Front frame (rear) |
590 |
|
6 |
Inner front pillar |
780 |
|
7 |
Inner hinge pillar |
590 |
|
8 |
Roof rail (inner) |
590 |
|
9 |
Roof rail reinforcement |
780 |
|
10 |
Front pillar reinforcement |
590 |
|
11 |
Hinge reinforcement (upper) |
590 |
|
12 |
Hinge reinforcement lower |
590 |
|
13 |
Side sill reinforcement |
780 |
|
14 |
Center pillar reinforcement (upper) |
980 |
|
15 |
Center pillar reinforcement (lower) |
590 |
|
16 |
Side sill reinforcement (rear) |
590 |
|
17 |
Suspension housing reinforcement (upper) |
780 |
|
18 |
Lower cowl side reinforcement (rear) |
590 |
|
19 |
Roof reinforcement No.2 |
590 |
|
20 |
Front B frame front |
590 |
|
21 |
Front B frame rear |
590 |
|
22 |
Floor reinforcement |
780 |
|
23 |
Crossmember No.2 |
590 |
|
24 |
Crossmember No.2.5 |
780 |
|
25 |
Tunnel reinforcement |
590 |
|
26 |
Side sill (inner, front) |
590 |
|
27 |
Side sill (inner, rear) |
780 |
|
28 |
Crossmember No.3 (lower) |
590 |
|
29 |
Rear frame reinforcement |
590 |
|
30 |
Rear side frame (front) |
590 |
|
31 |
Rear side frame (center) |
590 |
|
32 |
Rear side frame (rear) |
590 |
|
33 |
Floor side panel No.1 |
590 |
|
34 |
Rear bumper bracket |
590 |
Torque Box Removal [Panel Replacement]
Symbol Mark
Removal Procedure
1. Drill the 19 locations indicated by (A) shown in the figure.
NOTE:
When drilling the 19 locations indicated by (A) shown in the figure, do not
drill ...
Under Coating [Water Proof And Rust Preventive]
The shaded areas indicated under body locations that are undercoated to prevent
noise and rusting.
...
Other materials:
Engine Mount Disassembly/Assembly
No.1 Engine Mount (2WD)
1. Remove the front under cover No.2..
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
1
No.1 engine mount rubber
(See No.1 engine mount rubber removal note (2WD).)
(See No.1 engine mount inst ...
Liftgate Adjustment
1. Measure the gap and height difference between the liftgate and the body.
2. Loosen the liftgate hinge installation bolts and adjust the liftgate.
Standard clearance
a: 5.2?7.2 mm {0.21?0.28 in}
b: -2.0?0 mm {-0.078?0.000 in}
c: 3.8?6.2 mm {0.15?0.24 in}
d: ...
Suspension
49 T034 1A0
Coil spring compressor set
49 T028 3A0
Ball joint puller set
49 G033 102
Handle
49 U034 204
Dust boot installer
49 FT01 389
Pr ...
