Mazda CX-5 Service & Repair Manual: Shift Control Module Removal/Installation [C66 M R]
Removal
1. Shift the shift lever to the neutral position.
2. Remove the plug hole plate..
3. Disconnect the negative battery cable..
4. Remove the air cleaner and air hose as a single unit..
5. Remove the battery and battery tray..
6. Disconnect the control cable from the transaxle.
a. Pull the lock pin in the direction of the arrow shown in the figure and release the control cable end lock.
b. Press the tabs on the control cable and disconnect the control cable from the bracket on the transaxle.
7. Remove the neutral switch in the order shown in the figure
|
1 |
Connector |
|
2 |
Neutral switch |
|
3 |
Gasket |
8. Remove the detent ball pin in the order shown in the figure
|
1 |
Plug |
|
2 |
Gasket |
|
3 |
Spring |
|
4 |
Detent ball pin |
9. Remove the back-up light switch in the order shown in the figure
|
1 |
Connector |
|
2 |
Back-up light switch |
|
3 |
Gasket |
10. Remove the shift control module in the order shown in the figure
|
1 |
Breather |
|
2 |
Shift control module |
|
3 |
O-ring |
Installation
1. Verify that the shift control module is in the neutral position.
NOTE:
-
If the shift control module is in the neutral position, the shift lever with the weight can be moved up and down to a large extent.
2. Install the shift control module in the order shown in the figure
|
1 |
O-ring |
|
2 |
Shift control module |
|
3 |
Breather |
3. Install the back-up light switch in the order shown in the figure
|
1 |
Gasket |
|
2 |
Back-up light switch |
|
3 |
Connector |
4. Install the detent ball pin in the order shown in the figure
|
1 |
Detent ball pin |
|
2 |
Spring |
|
3 |
Gasket |
|
4 |
Plug |
5. Install the neutral switch in the order shown in the figure
|
1 |
Gasket |
|
2 |
Neutral switch |
|
3 |
Connector |
6. Connect the control cable to the transaxle.
7. Make sure that the shift lever can be shifted smoothly.
8. Install the battery tray and battery..
9. Install the air cleaner and air hose as a single unit..
10. Connect the negative battery cable..
11. Install the plug hole plate..
Shift And Select Mechanism [C66 M R]
Purpose, Function
The shift and select mechanism moves the shift fork to change gears according
to the operation of the shift lever in the cabin.
Construction
Shift control module ...
Shift Lock System Inspection
Shift-Lock System Inspection
1. Switch the ignition ON (engine off).
2. Shift the selector lever to the P position.
3. Verify that the selector lever cannot be shifted from P to R position when
...
Other materials:
Manual Transaxle Oil Replacement [C66 M R]
1. Park the vehicle on level ground.
2. Remove the front under cover No.2..
3. Remove the drain plug and gasket, and drain the manual transaxle oil.
4. Install a new gasket and the drain plug.
Tightening torque
39—59 N·m {4.0—6.0 kgf·m, 29—43 ft·lbf}
5. Remove the ...
Pre Delivery Inspection
Pre?Delivery Inspection Table
Exterior
INSPECT and ADJUST, if necessary, the following items to specification:
?Glass, exterior bright metal and paint for damage
?Wheel lug nuts
?All weatherstrips for damage or detachment
?Adjust tire pressures to specification
Adjust the tire pr ...
Air Fuel Ratio (A/F) Sensor Heater Control [Skyactiv G 2.0]
Outline
Based on the control of the A/F sensor heater, a stabilized oxygen concentration
is detected even at low exhaust temperatures, and feedback control of fuel injection
even at cold engine start is made possible for improved cold temperature exhaust
emission performance.
...
