Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Rear Wiper System

Outline

Structural View


System Wiring Diagram


Operation

Continuous operation

1. When the rear wiper and washer switch is turned to the ON position with the ignition switched ON (engine off or on) (1), the start stop unit detects a rear wiper switch ON signal.(2)

2. When the start stop unit detects a rear wiper switch ON signal, it send a rear wiper switch position signal (LO) to the front body control module (FBCM) as a CAN signal.(3)

3. When the front body control module (FBCM) receives the rear wiper switch position signal (LO), it sends a rear wiper operation request signal to the rear body control module (RBCM) via the instrument cluster as a CAN signal.(4)

4. When the rear body control module (RBCM) receives the rear wiper operation request signal, it supplies the gate current from the internal CPU to FET B (5), and current flows from the battery to the rear wiper motor and the rear wiper operates continuously.(6)

NOTE:


Auto-stop operation

1. If the wiper and washer switch is set to the OFF position (1), the rear wiper operation request signal sent to the rear body control module (RBCM) via the instrument cluster from the front body control module (FBCM) turns off. (2)

2. When the rear wiper operation request signal turns off, the rear body control module (RBCM) turns the FET B off. (3)

3. The autostop switch in the rear wiper motor turns off if the rear wiper stops at the correct position, and the rear wiper stops based on this.(4)


Intermittent wiper operation

1. When the rear wiper and washer switch is moved to the INT position with the ignition switched ON (engine off or on) (1), the start stop unit detects a rear wiper switch signal (INT).(2)

2. When the start stop unit detects a rear wiper switch signal (INT), it send a rear wiper switch position signal (INT) to the front body control module (FBCM) as a CAN signal.(3)

3. When the front body control module (FBCM) receives the rear wiper switch position signal (INT), it sends a rear wiper operation request signal to the rear body control module (RBCM) via the instrument cluster as a CAN signal.(4)

4. When the rear body control module (RBCM) receives the rear wiper operation request signal, it supplies the gate current from the internal CPU to FET B (5), and current flows from the battery to the rear wiper motor and the rear wiper operates.(6)

NOTE:

5. The front body control module (FBCM) sends a rear wiper operation request signal to the rear body control module (RBCM) via the instrument cluster at regular intervals. Due to this, the rear wiper operates intermittently.(7)


Synchronized washer and wiper operation

1. When the rear wiper and washer switch is turned to the rear washer position with the ignition switched ON (engine off or on) (1), the start stop unit detects a rear washer switch ON signal.(2)

2. When the start stop unit detects a rear washer switch ON signal, it send a rear washer operation request signal to the front body control module (FBCM) as a CAN signal.(3)

3. When the front body control module (FBCM) receives the rear washer operation request signal, it supplies the base current from the internal CPU to transistor (4), and collector current flows from the internal power supply (5), turning the rear washer relay on.(6)

4. When the rear washer relay is turned on, current flows to the washer motor and the washer motor operates, and washer fluid is sprayed from the rear washer nozzle.(7)

5. When the front body control module (FBCM) receives the rear washer operation request signal for a certain period of time, it sends a rear wiper operation request signal to the rear body control module (RBCM) via the instrument cluster as a CAN signal.(8)

6. When the rear body control module (RBCM) receives the rear wiper operation request signal, it operates the rear wiper.(9)

7. When the rear washer switch is turned off, the rear wiper stops after it operates for approx. 2.6 s

.


Rear Wiper Motor Removal/Installation
1. Disconnect the negative battery cable.. 2. Remove the following parts: a. Rear wiper arm and blade. b. Liftgate upper trim. c. Liftgate side trim. d. Liftgate recess. e. Liftgate lower ...

Windshield Wiper Arm And Blade Adjustment
1. Switch the ignition ON (engine off or on). 2. Operate the windshield wiper at low speed. 3. Verify that the windshield wiper operates at low speed and stop the windshield wiper. 4. Verify t ...

Other materials:

Quick Release Connector Removal/Installation
WARNING: Fuel is very flammable liquid. If fuel spills or leaks from the pressurized fuel system, it will cause serious injury or death and facility breakage. Fuel can also irritate skin and eyes. To prevent this, always complete the “Fuel Line Safety Procedure”, while referring ...

Fully Automatic Type
Climate control information is displayed on the display. Control Switches AUTO switch By pressing the AUTO switch the following functions will be automatically controlled in accordance with the selected set temperature: • Airflow temperature • Amount of airflow • Selection of airflow ...

Tcs/DSC Indicator Light
Purpose/Function The TCS/DSC indicator light, built into the instrument cluster, informs the driver of the following vehicle conditions. TCS is operating. (Drive wheel is slipping.) DSC is operating. (Vehicle side-slip condition.) Roll over mitigation (RO ...

© 2016-2024 Copyright www.mcx5.org