Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Rear Upper Arm Removal/Installation [2 Wd]

Mazda CX-5 Service & Repair Manual / Suspension / Rear Suspension / Rear Upper Arm Removal/Installation [2 Wd]

WARNING:

  1. Verify that the crossmember is securely supported by a jack. If the rear crossmember falls off, it can cause serious injury or death, and damage to the vehicle.

CAUTION:

NOTE:

1. Disconnect the auto leveling sensor link. (With auto leveling sensor).


2. Disconnect the wiring harness clips and connector installed to the rear crossmember. (With auto leveling sensor)


3. Disconnect the rear ABS wheel-speed sensor wiring harness installed to the hub support and set it aside..


4. Remove the TWC..

5. Remove the rear coil spring..

6. Remove in the order indicated in the table.

7. Install in the reverse order of removal.

8. Inspect the wheel alignment and adjust it if necessary..



1

Rear upper arm

(See Rear Upper Arm Removal Note.)

(See Rear Upper Arm Installation Note.)

2

Rear upper arm bushing

(See Rear Upper Arm Bushing Removal Note.)

(See Rear Upper Arm Bushing Installation Note.)


Rear Upper Arm Removal Note

1. Jack up the vehicle to the unloaded condition, and support the rear trailing link component using a jack.


2. Align the rear crossmember component and rear upper arm and mark them.


3. Support the rear crossmember component with a jack and remove the rear crossmember installation nuts.


4. Press down on the rear crossmember component slowly until the rear upper arm inside installation bolts can be removed using a jack.


5. Remove the rear upper arm.

Rear Upper Arm Bushing Removal Note

1. Mark the rear upper arm as shown in the figure.


2. Press the rear upper arm bushing out using the SSTs

.

CAUTION:


Rear Upper Arm Bushing Installation Note

1. Mark the new rear upper arm bushing as shown in the figure.


H1: 6.0 mm {0.24 in}

2. Align the projection of a new rear upper arm bushing with the marks placed during removal.


3. Press fit the rear upper arm bushing until the marks placed in Step 1 cannot be seen using the SSTs.

CAUTION:


NOTE:


H2: 49.5 mm {1.95 in} H3: 44.5 mm {1.75 in}

4. After installing the rear upper arm bushing, verify that it is installed to the position shown in the figure.


H4: 24.0±0.6 mm {0.945±0.02 in}

Rear Upper Arm Installation Note

1. Place alignment mark on the new rear upper arm in the same positions as the removed rear upper arm.


2. Install the rear upper arm.

3. Lift up the rear crossmember component using a jack and install the rear crossmember installation nuts.


Rear Suspension
Outline E-type multi-link rear suspension has been adopted. The longitudinal span of the rear crossmember was extended and the longitudinal offset of the rear lateral link ...

Rear Upper Arm Removal/Installation [Awd]
WARNING: Verify that the crossmember is securely supported by a jack. If the rear crossmember falls off, it can cause serious injury or death, and damage to the vehicle. CAUTIO ...

Other materials:

Lights On Indicator Light
Purpose Notifies the user that the TNS or the headlights (LO) are on. Function Illuminates when the illumination conditions for the TNS, headlights (LO), or parking lights are met. When the instrument cluster receives the TNS malfunction signal sent via CAN communic ...

Room Light Control System
Outline The room light control system changes the illumination condition and illumination level of the interior lights (door position) according to whether the doors are opened/closed and locked/unlocked. The room light control system is controlled by the rear body control modul ...

Rear Seat Belt Removal/Installation
CAUTION: The ELR (emergency locking retractor) has a spring that will unwind if the retractor cover is removed. The spring cannot be rewound by hand. If this occurs, the ELR will not work properly. Therefore, do not disassemble the retractor. 1. Remove the following parts: a. T ...

© 2016-2022 Copyright www.mcx5.org