Mazda CX-5 Service & Repair Manual: Rear Drive Shaft Removal/Installation
CAUTION:
-
Performing the following procedures without first removing the ABS wheel?speed sensor may possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the following procedures, remove the ABS wheel?speed sensor (wheel side) and fix it to an appropriate place where the sensor will not be pulled by mistake while the vehicle is being serviced.
1. Drain the rear differential oil into a container..
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
4. After installation, add the specified rear differential oil..
5. Inspect the rear wheel alignment and adjust it if necessary..
|
1 |
Locknut (See Locknut Installation Note.) |
|
2 |
ABS wheel-speed sensor . |
|
3 |
Brake hose clip |
|
4 |
Brake caliper component |
|
5 |
Disc plate |
|
6 |
Bolt (wheel hub) (See WHEEL HUB COMPONENT REMOVAL/INSTALLATION [2WD].) |
|
7 |
Wheel hub (See Wheel Hub Removal Note.) |
|
8 |
Dust cover |
|
9 |
Rear drive shaft (See Rear Drive Shaft Removal Note.) |
|
10 |
Clip (See Clip Installation Note.) |
Wheel Hub Removal Note
1. Before removing the wheel hub, place alignment marks on the wheel hub and the hub support so that they can be installed to the same position before removal.
2. Remove the wheel hub.
CAUTION:
-
Be careful not to damage the rear differential oil seal.
-
Be careful not to damage the drive shaft boots and ABS sensor rotor.
Rear Drive Shaft Removal Note
1. Pull the drive shaft toward the wheel side, then remove the drive shaft.
Clip Installation Note
1. Install a new clip onto the joint shaft with the opening facing upward. Ensure that the diameter of the clip does not exceed the specification on installation.
2. After installation, measure the outer diameter. If it exceeds the specification, repeat Steps 1—2 using a new clip.
-
Clip outer diameter specification
-
25.2 mm {0.992 in} max.
Locknut Installation Note
1. After tightening the locknut once at a torque of 390 N·m {40 kgf·m, 288 ft·lbf}
, return it temporarily 180 degrees
, then retighten it to a torque of 236—274 N·m {25—27 kgf·m, 175—202 ft·lbf}
.
Rear Drive Shaft Inspection
1. Inspect each connecting part for looseness.
Tighten or replace parts if necessary.
2. Inspect the dust boot on the drive shaft for cracks, damage, leaking grease,
and loosenes ...
Rear Lateral Link Removal/Installation
1. Disconnect the rear stabilizer control link lower side nut..
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
4. Inspect the wheel alignment an ...
Other materials:
Rear Heat Duct Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Decoration panel.
b. Shift lever knob (MTX).
c. Front console box.
d. Shift panel.
e. Upper panel.
f. Rear console.
g. Side wall.
h. Front console.
i. Front scuff plate.
j. Front side trim.
k. Joint ...
Room Light Control System
Outline
The room light control system changes the illumination condition and illumination
level of the interior lights (door position) according to whether the doors
are opened/closed and locked/unlocked.
The room light control system is controlled by the rear body control modul ...
Rear Beltline Molding Removal/Installation
CAUTION:
Affix protective tape to the position shown in the figure.
1. Fully open the rear door glass.
2. Insert a tape-wrapped flathead screwdriver and then detach the clip A in the
direction of arrow (1) shown in the figure.
3. Pull up the rear belt line molding in the di ...
