Mazda CX-5 Service & Repair Manual: Oil Seal (Differential) Replacement [Fw6 A EL, Fw6 Ax EL]

Mazda CX-5 Service & Repair Manual / Drivetrain / Driveline / Differentials / Oil Seal (Differential) Replacement [Fw6 A EL, Fw6 Ax EL]

Transaxle Case Side

1. Remove the front under cover No.2..

2. Drain the ATF..

3. Disconnect the drive shaft (LH) from the transaxle..

CAUTION:

The oil seal is easily damaged by the sharp edges of the drive shaft splines. Do not let the splines contact the oil seal.

4. Remove the oil seal using a tape-wrapped flathead screwdriver.

5. Using the SSTs

and a hammer, tap a new oil seal in evenly until the SST

(49 U027 003) contacts the transaxle case.

6. Coat the lip of the oil seal with ATF.

7. Install the drive shaft (LH) to the transaxle..

8. Add the ATF..

9. Install the front under cover No.2..

10. Perform the “Mechanical System Test”..

Converter housing Side (FW6A-EL)

1. Remove the front under cover No.2..

2. Drain the ATF..

3. Disconnect the drive shaft (RH)..

CAUTION:

The oil seal is easily damaged by the sharp edges of the drive shaft splines. Do not let the splines contact the oil seal.

4. Remove the oil seal using a tape-wrapped flathead screwdriver.

5. Using the SSTs

and a hammer, tap a new oil seal in evenly until the SST

(49 U027 003) contacts the transaxle case.

6. Coat the lip of the oil seal with ATF.

7. Install the drive shaft (RH)..

8. Add the ATF..

9. Install the front under cover No.2..

10. Perform the “Mechanical System Test”..

Converter housing Side (FW6AX-EL)

1. Remove the front under cover No.2..

2. Drain the ATF..

3. Remove the transfer..

CAUTION:

The oil seal is easily damaged by the sharp edges of the drive shaft splines. Do not let the splines contact the oil seal.

4. Remove the oil seal using a tape-wrapped flathead screwdriver.

5. Using the SSTs

and a hammer, tap a new oil seal in evenly until the SST

(49 U027 003) contacts the transaxle case.

6. Coat the lip of the oil seal with ATF.

7. Install the transfer..

8. Add the ATF..

9. Install the front under cover No.2..

10. Perform the “Mechanical System Test”..

Oil Seal (Differential) Replacement [C66 M R]

1. Remove the front under cover No.2.. 2. Drain the manual transaxle oil.. 3. Disconnect the drive shaft (LH) from the MTX.. 4. Disconnect the drive shaft (RH) from the MTX.. 5. Remove the oil ...

Rear Differential

Purpose, Function A rear differential with an integrated coupling component has been adopted, reducing size and weight. An aluminum differential carrier has been adopted, reducing we ...

Other materials:

Manual Type
Control Switches Temperature control dial This dial controls temperature. Turn it clockwise for hot and counterclockwise for cold. NOTE When the mode is set to or with the fan control dial in a position other than 0 and the temperature control dial in the maximum cold position, the air int ...

Electric Power Steering (Eps) Motor
Purpose, Function The EPS motor is driven by the control current from the EPS CM (control module) and generates assist torque to manual steering mechanism. Construction The EPS motor is installed to the steering column with an integrated EPS CM. The EPS motor is a b ...

Auto Leveling Sensor
Purpose Detects the vehicle height and outputs it to the AFS control module. Function Changes the detected vehicle height into a voltage value and outputs it to the AFS control module. Construction Installed to the rear cross member. Consists of link No. 1 ...