Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Oil Pressure Switch Removal/Installation [Fw6 A EL, Fw6 Ax EL]

Mazda CX-5 Service & Repair Manual / Engine / Lubrication / Oil Pressure Switch Removal/Installation [Fw6 A EL, Fw6 Ax EL]

WARNING:

CAUTION:

Oil Pressure Switch A

1. Select the selector lever to P position.

2. Disconnect the negative battery cable..

3. Remove the front under cover No.2..

4. Clean the transaxle exterior throughout with a steam cleaner or cleaning solvents.

5. Remove the air cleaner component..

6. Remove the control valve body..

7. Remove the oil seal (control valve body)..

8. Insert a precision flathead screwdriver and move it in the direction of the arrow to disconnect the oil pressure switch A connector as shown in the figure.


CAUTION:

9. Remove the oil pressure switch A fitting bolts.


10. Detach tab shown in the figure and remove the oil pressure switch A from the control valve body.


11. Install the oil pressure switch A to the control valve body.


12. Verify that the tab is attached correctly.

13. Install the oil pressure switch A fitting bolts.


14. Connect the oil pressure switch A connector.


15. Install the control valve body..

16. Install the front under cover No.2..

17. Install the oil seal (control valve body)..

18. Install the hose clamp..

19. Connect the control valve body connector..

CAUTION:

20. Add the ATF..

21. Install the air cleaner component..

22. Connect the negative battery cable..

23. Perform the “Initial Learning” (oil pressure switch A Replacement)..

24. Perform the “Mechanical System Test”..

Oil Pressure Switch B

1. Disconnect the negative battery cable..

2. Remove the front under cover No.2..

3. Clean the transaxle exterior throughout with a steam cleaner or cleaning solvents.

4. Drain the ATF..

5. Remove the oil pan.

CAUTION:

6. Remove the oil strainer..

7. Remove the oil strainer O-ring..

8. Insert a precision flathead screwdriver and move it in the direction of the arrow to disconnect the oil pressure switch B connector as shown in the figure.


CAUTION:

9. Remove the oil pressure switch B.


10. Install the oil pressure switch B.


11. Connect the oil pressure switch B connector.


12. Install the oil strainer O-ring..

NOTE:

13. Install the oil strainer..

14. Apply a light coat of silicon sealant (TB1217E) to the contact surfaces of the oil pan and transaxle case.


CAUTION:

15. Install the oil pan with new bolts before the applied sealant starts to harden.

16. Install the front under cover No.2..

17. Add the ATF..

18. Connect the negative battery cable..

19. Perform the “Initial Learning” (oil pressure switch B Replacement)..

20. Perform the “Mechanical System Test”..

Oil Pressure Switch Inspection
1. Switch the ignition ON (engine off) and verify that the oil pressure warning light is illuminated. 2. Start the engine and verify that the oil pressure warning light turns off. If the ...

Oil Pressure Switch [Fw6 A EL, Fw6 Ax EL]
Purpose/Function The oil pressure switch detects the engagement pressures of the low clutch, 2-6 brake, R-3-5 brake, and the high clutch. The oil pressure switch signal is used for a ...

Other materials:

Audio Control Switch Operation
When the audio unit is turned on, operation of the audio unit from the steering wheel is possible. NOTE Because the audio unit will be turned off under the following conditions, the switches will be inoperable. • When the ignition is switched off. • When the power button on the audio uni ...

Head Restraints
Your vehicle is equipped with head restraints on all outboard seats and the rear center seat. The head restraints are intended to help protect you and the passengers from neck injury. WARNING Always drive with the head restraints installed when seats are being used and make sure they are pro ...

Miller Cycle Engine
Outline The Miller cycle engine is a high-efficiency engine which achieves high fuel economy performance by obtaining a high-expansion ratio. The Miller cycle engine achieves a high-expansion ratio without increasing its effective compression ratio by retarding the intake air va ...

© 2016-2024 Copyright www.mcx5.org