Chevrolet Spark manuals

Mazda CX-5 Owners Manual: Meters and Gauges


1 Speedometer

2 Odometer, Trip Meter and Trip Meter Selector

3 Tachometer

4 Fuel Gauge

5 Dashboard Illumination

6 Outside Temperature Display

7 Trip Computer and INFO Switch

Speedometer

The speedometer indicates the speed of the vehicle.

Odometer, Trip Meter and Trip Meter Selector

The display mode can be changed between trip meter A and trip meter B by pressing the selector while one of them is displayed. The selected mode will be displayed.


NOTE

When the ignition is switched to ACC or OFF, the odometer or trip meters cannot be displayed, however, pressing the selector button can inadvertently switch the trip meters or reset them during an approximate tenminute period in the following cases:

After the ignition is switched to OFF from ON.

After the driver's door is opened.

Odometer

The odometer records the total distance the vehicle has been driven.

Trip meter

The trip meter can record the total distance of two trips. One is recorded in trip meter A, and the other is recorded in trip meter B.

For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the fuel tank is filled.

When trip meter A is selected, pressing the selector again within one second will change to trip meter B mode.

When trip meter A is selected, TRIPA will be displayed. When trip meter B is selected, TRIP B will be displayed.

The trip meter records the total distance the vehicle is driven until the meter is again reset. Return it to “0.0” by holding the selector depressed for 1 second or more. Use this meter to measure trip distances and to compute fuel consumption.

NOTE

Only the trip meters record tenths of kilometers (miles).

The trip record will be erased when:

The power supply is interrupted (blown fuse or the battery is disconnected).

The vehicle is driven over 9999.9 km (mile).

Tachometer

The tachometer shows engine speed in thousands of revolutions per minute (rpm).


CAUTION

Do not run the engine with the tachometer needle in the RED ZONE.

This may cause severe engine damage.

Fuel Gauge

The fuel gauge shows approximately how much fuel is remaining in the tank when the ignition is switched ON. We recommend keeping the tank over 1/4 full.


If the low fuel warning light illuminates or the fuel level is very low, refuel as soon as possible.

Refer to Warning/Indicator Lights on .

NOTE

After refueling, it may require some time for the indicator to stabilize. In addition, the indicator may deviate while driving on a slope or curve since the fuel moves in the tank.

The direction of the arrow (
) indicates that the fuel-filler lid is on the left side of the vehicle.

Dashboard Illumination

Rotate the knob to adjust the brightness of the instrument cluster and other illuminations in the dashboard.

NOTE

The brightness of dashboard illuminations can be adjusted when the headlight switch is in the or
position.


When the dashboard illumination brightness cannot be adjusted any more, a beep sound will be heard.


Canceling the illumination dimmer

When the headlight switch is in the or
position, the illumination of the
instrument cluster dims.

When driving on snowy or foggy roads, or in other situations when the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer and increase the illumination intensity.

To cancel the illumination dimmer, rotate the knob clockwise fully. You will hear a beep sound and the illumination dimmer will be canceled.

NOTE

This symbol ( ) indicates the knob to adjust the brightness
of the dashboard illumination.

If the dashboard illumination knob is kept at the illumination dimmer cancel position, the instrument cluster will not dim when the headlight switch is turned to the or
position again. Rotate the dashboard
illumination knob counterclockwise to activate the illumination dimmer.

Outside Temperature Display

When the ignition is switched ON, the outside temperature is displayed.


NOTE

Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:

Significantly cold or hot temperatures.

Sudden changes in outside temperature.

The vehicle is parked.

The vehicle is driven at low speeds.

The outside temperature unit can be switched between Celsius and Fahrenheit using the following procedure.

1. Press the INFO button with the ignition switched off and continue pressing the INFO button for 5 seconds or longer while switching the ignition ON. The outside temperature display flashes.

2. Press the up or down
part of the INFO switch to change the
outside temperature unit.

3. Press and hold the INFO button for 3 seconds or longer while the outside temperature display is flashing. The outside temperature display illuminates.

Trip Computer and INFO Switch

The following information can be selected by pressing the up or down
part of the INFO switch with the ignition
switched ON.

The approximate distance you can travel on the available fuel.

The average fuel economy.

The current fuel economy.

The average vehicle speed.

If you have any problems with your trip computer, consult an Authorized Mazda Dealer.

Distance-to-empty mode

This mode displays the approximate distance you can travel on the remaining fuel based on the fuel economy.

The distance-to-empty will be calculated and displayed every second.


NOTE

Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refueling is required, refuel as soon as possible if the fuel level is very low or the low fuel warning light illuminates.

The display will not change unless you add more than approximately 10 L (2.6 US gal, 2.2 Imp gal) of fuel.

The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge indicating the remaining fuel supply disappear.

Average fuel economy mode

This mode displays the average fuel economy by calculating the total fuel consumption and the total traveled distance since purchasing the vehicle, reconnecting the battery after disconnection, or resetting the data. The average fuel economy is calculated and displayed every minute.


To clear the data being displayed, press the INFO button for more than 1.5 seconds.

After pressing the INFO button, - - - L/ 100 km (- - - mpg) will be displayed for about 1 minute before the fuel economy is recalculated and displayed.

Current fuel economy mode

This mode displays the current fuel economy by calculating the amount of fuel consumption and the distance traveled.

Current fuel economy will be calculated and displayed every 2 seconds.


When you've slowed to about 5 km/h (3 mph), - - - L/100 km (- - - mpg) will be displayed.

Average vehicle speed mode

This mode displays the average vehicle speed by calculating the distance and the time traveled since connecting the battery or resetting the data.

Average vehicle speed will be calculated and displayed every 10 seconds.


To clear the data being displayed, press the INFO button for more than 1.5 seconds. After pressing the INFO button, - - - km/h (- - - mph) will be displayed for about 1 minute before the vehicle speed is recalculated and displayed.

Instrument Cluster and Display
...

Warning/Indicator Lights
Warning (Display Indication) Message information such as system operations or malfunctions is indicated in the display. Check the vehicle condition or have the vehicle inspected at an Autho ...

Other materials:

Tires
For reasons of proper performance, safety, and better fuel economy, always maintain recommended tire inflation pressures and stay within the recommended load limits and weight distribution. WARNING Using Different Tire Types: Driving your vehicle with different types of tires is dangerous. It ...

Lighting System Personalization
A personalization function has been adopted with which settings for each function can be changed. The following settings for the auto light system and interior light control system can be changed as desired. There are two types of customization procedures; one using the M ...

Front Lower Arm Removal/Installation
1. Remove the front under cover No.2.. 2. Remove in the order indicated in the table. 3. Install in the reverse order of removal. 4. Inspect the wheel alignment and adjust it if necessary.. 1 Front lower arm ball joint 2 Front lower arm ...

© 2016-2024 Copyright www.mcx5.org