Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Mechanical

Outline

*1 Resistance (friction force) which occurs when two object slide against each other. The larger the sliding resistance, the greater the energy loss.

*2 Energy loss which occurs from each type of resistance corresponding to intake and exhaust is called pumping loss.

Structural View


Structure


Cylinder head cover

(See CYLINDER HEAD COVER [SKYACTIV-G 2.0].)

Cylinder head

(See CYLINDER HEAD [SKYACTIV-G 2.0].)

Cylinder head gasket

(See CYLINDER HEAD GASKET [SKYACTIV-G 2.0].)

Cylinder block

(See CYLINDER BLOCK [SKYACTIV-G 2.0].)

Crankshaft

(See CRANKSHAFT, MAIN BEARING [SKYACTIV-G 2.0].)

Piston

(See PISTON, PISTON RING, PISTON PIN [SKYACTIV-G 2.0].)

Connecting rod

(See CONNECTING ROD, CONNECTING ROD BEARING [SKYACTIV-G 2.0].)

Engine front cover

(See ENGINE FRONT COVER [SKYACTIV-G 2.0].)

Crankshaft pulley

(See CRANKSHAFT PULLEY [SKYACTIV-G 2.0].)

Drive belt

(See DRIVE BELT [SKYACTIV-G 2.0].)

Valve mechanism

(See VALVE MECHANISM [SKYACTIV-G 2.0].)

Valve

(See VALVE, VALVE SPRING, VALVE SEAL, VALVE GUIDE [SKYACTIV-G 2.0].)

HLA

(See HYDRAULIC LASH ADJUSTER, ROCKER ARM [SKYACTIV-G 2.0].)

Camshaft

(See CAMSHAFT [SKYACTIV-G 2.0].)

Timing chain

(See TIMING CHAIN, CHAIN TENSIONER [SKYACTIV-G 2.0].)

Variable valve timing mechanism

(See VARIABLE VALVE TIMING MECHANISM [SKYACTIV-G 2.0].)

OCV

(See OIL CONTROL VALVE (OCV) [SKYACTIV-G 2.0].)

Hydraulic variable valve timing actuator

(See HYDRAULIC VARIABLE VALVE TIMING ACTUATOR [SKYACTIV-G 2.0].)

Electric variable valve timing actuator

(See ELECTRIC VARIABLE VALVE TIMING ACTUATOR [SKYACTIV-G 2.0].)

Electric variable valve timing relay

(See ELECTRIC VARIABLE VALVE TIMING RELAY [SKYACTIV-G 2.0].)

Engine mount

(See ENGINE MOUNT [SKYACTIV-G 2.0].)


Hydraulic Variable Valve Timing Actuator
Purpose, Function The hydraulic variable valve timing actuator operates according to the hydraulic pressure and changes the phases of the exhaust camshaft. As a result, the open/close per ...

Miller Cycle Engine
Outline The Miller cycle engine is a high-efficiency engine which achieves high fuel economy performance by obtaining a high-expansion ratio. The Miller cycle engine achieves a high- ...

Other materials:

Rear Buckle Removal/Installation
1. Switch the ignition to off. 2. Disconnect the negative battery cable and wait for 1 min or more.. 3. Press the release switch, then disconnect the rear center seat belt and rear buckle. 4. Fold down the rear seat back. 5. Remove the trunk board.. 6. Remove the bolt. 7. Remo ...

Break-In Period
No special break-in is necessary, but a few precautions in the first 1,000 km (600 miles) may add to the performance, economy, and life of your Mazda. • Do not race the engine. • Do not maintain one constant speed, either slow or fast, for a long period of time. • Do not drive constantl ...

Side Step Molding Removal/Installation
1. Set the rear over fender aside.. 2. Insert a tape-wrapped flathead screwdriver shown in the figure and remove the clip A in the direction of arrow (1). 3. Slide the side step molding in the direction of the arrow (2) shown in the figure and remove clips B from side step molding. 4. ...

© 2016-2022 Copyright www.mcx5.org