Mazda CX-5 Service & Repair Manual
Mazda CX-5 Service & Repair Manual
- Vehicle General
- How To Use This Manual
- Abbreviations
- Body And Accessories SST
- Front Wiring Harness Protector Removal/Installation
- Identification Number Locations
- Jacking Positions, Vehicle Lift (2 Supports) And Safety Stand (Rigid Rack) Positions
- Personalization Features
- Pre Delivery Inspection
- Push Button Start Inspection
- Push Button Start Removal/Installation
- Sae Standards
- Service Cautions
- St 001/12 Special Service Tool Shipment January 2013
- Units
- Vehicle Identification Number (VIN) Code
- Accessories
- Cruise Control
- Electronics
- Power Sockets
- Safety Systems
- Security & Keyless Entry
- Storage
- Trailer
- Body
- Doors/Lids & Hood/Trunk
- Body Exterior, Frame
- Glass & Windows
- Horn
- Driver Info & Control
- Body Interior
- Lighting & Horn
- Mirrors
- Roof - Fixed, Leisure
- Seats
- Wipers, Washers
- Brakes
- General
- Brake Control, Vehicle Dynamics
- Disc Brakes
- Parking Brake
- Sensors, Switches, Relays
- Drivetrain
- Driveline
- Transmission/Transaxle
- Electrical
- General
- Battery
- Fuses & Junction Blocks
- Ground Distribution
- Ignition
- Data Network
- Starting, Charging
- Engine
- General
- Belts, Hoses, Pulleys
- Control
- Cooling
- Emissions
- Engine Assembly
- Exhaust & Emissions
- Forced Induction
- Fuel
- Intake
- Lubrication
- HVAC
- General
- A/C
- Restraints
- Restraints
- Restraints SST
- Adjuster Anchor Removal/Installation
- Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Standard Deployment
Control System]
- Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Two Step Deployment
Control System]
- Air Bag Module And Pre Tensioner Seat Belt Disposal Procedures [Standard Deployment
Control System]
- Air Bag Module And Pre Tensioner Seat Belt Disposal Procedures [Two Step Deployment
Control System]
- Buckle Switch Inspection
- Front Buckle Removal/Installation
- Front Seat Belt Removal/Installation
- Lap Pre Tensioner Seat Belt [Two Step Deployment Control System]
- Pre Tensioner Seat Belt [Standard Deployment Control System]
- Pre Tensioner Seat Belt [Two Step Deployment Control System]
- Rear Buckle Removal/Installation
- Rear Seat Belt Removal/Installation
- Seat Belt
- Seat Belt Inspection
- Steering
- General
- Linkage, Power
- Wheel, Column
- Suspension
- General
- Front Suspension
- Rear Suspension
- Wheels, Tires
Personalization Features
...
Other materials:
Canister Vent (Cv) Solenoid Valve Inspection
U.S.A. And CANADA
Airflow inspection
1. Disconnect the negative battery cable..
2. Remove the CV solenoid valve..
3. Inspect airflow between the ports under the following conditions.
Measured condition
Continuity between A—B
When volta ...
Adaptive Front Lighting System (Afs) Off Switch Inspection
1. Disconnect the negative battery cable..
2. Remove the switch panel..
3. Verify that the resistance between AFS OFF switches B and C is as indicated
in the table.
If the resistance can be verified as indicated in the table, go to the next
step.
If not as indicated ...
Front Door Latch Switch Inspection
1. Perform the front door glass preparation..
2. Disconnect the negative battery cable..
3. Remove the following parts:
a. Inner garnish.
b. Front door trim.
c. Front door glass.
d. Front door module panel.
e. Front door key cylinder.
f. Front door latch and lock actuator.
4. Verif ...
© 2016-2026 Copyright www.mcx5.org
