Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Liftgate Light Removal/Installation

Mazda CX-5 Service & Repair Manual / Body / Doors/Lids & Hood/Trunk / Liftgate Light Removal/Installation

NOTE:

1. Disconnect the negative battery cable..

2. Insert a tape-wrapped flathead screwdriver into the service hole in the position shown in the figure.


3. Move the flathead screwdriver in the direction of the arrow (1) shown in the figure, pull out the service hole cover from the liftgate, and detach the service hole cover tab A, B and liftgate.


4. Pull out the service hole cover in the direction of the arrow (2) shown in the figure and pull out the service hole cover hook C from the liftgate.


5. Remove the service hole cover.

6. Insert a flathead screwdriver into the service hole in the position shown in the figure.


7. Move the flathead screwdriver in the direction of the arrow (3) shown in the figure, pull out the service hole cover No.1, and detach the service hole cover No.1 tab D from the bracket.


8. Remove the service hole cover No.1.


9. Insert a flathead screwdriver into the service hole in the position shown in the figure.


10. Move the flathead screwdriver in the direction of the arrow (4) shown in the figure, pull out the service hole cover No.2, and detach the service hole cover No.2 tab E from the bracket.


11. Remove the service hole cover No.2.


12. Insert the flathead screwdriver into the clearance between the bracket tab F and the liftgate light shown in the figure.


13. Move the flathead screwdriver in the direction of the arrow (5) shown in the figure, pull out the bracket in the direction of the arrow (6) shown in the figure while pressing the bracket tab, and detach the bracket tab G and liftgate light.


14. Insert the flathead screwdriver into the clearance between the bracket tab and the liftgate light shown in the figure.


15. Move the flathead screwdriver in the direction of the arrow (7) shown in the figure, pull the bracket in the direction of the arrow (8) shown in the figure, and detach the bracket tab H, I, J and liftgate light.


16. Move the bracket in the direction of arrow (9) shown in the figure to pull out hook K of the bracket from the liftgate.


17. Move the bracket in the direction of arrow (10) shown in the figure to detach tab L of the bracket from the liftgate light, then pull out hook M of the bracket from the liftgate and remove the bracket.


18. Rotate the socket in the direction of the arrow (11) shown in the figure and remove it from the liftgate light in the direction of the arrow (12) shown in the figure.


19. Remove the cap nut.


20. Push out the liftgate light in the direction of the arrow (13) shown in the figure and remove it from the liftgate.


CAUTION:

21. Install in the reverse order of removal.

Liftgate Light
Purpose The liftgate lights are used to signal the following conditions to vehicles/people at the rear. Back-up lights: Signals that the vehicle is backing up. Tailli ...

Liftgate Lock Striker Removal/Installation
1. Remove the trunk end trim.. 2. Remove the bolts, then remove the liftgate lock striker. 3. Install in the reverse order of removal. 4. Adjust the liftgate.. ...

Other materials:

Tweeter Inspection
1. Disconnect the negative battery cable.. 2. Remove the side speaker grille.. 3. Remove the tweeter.. 4. Verify that the resistance between the tweeter terminals is as indicated in the table. If not as indicated in the table, replace the tweeter. Without Bose® With B ...

Fuel Pump Control
Outline By switching the fuel pump discharge amount, reduced power consumption and improved fuel economy have been realized. The PCM determines the optimum fuel pump drive force according to the engine operation conditions, and sends the fuel pump drive signal to the fuel pump ...

Front Sash Molding Installation
WARNING: Using a utility knife with bare hands can cause injury. Always wear gloves when using a utility knife. NOTE: Double-sided adhesive tape has already been attached to the new front sash molding. 1. When installing a new front sash molding, follow the procedur ...

© 2016-2022 Copyright www.mcx5.org