Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Fuel Tank Inspection

Mazda CX-5 Service & Repair Manual / Engine / Fuel / Fuel Tank Inspection

WARNING:

NOTE:

2WD

1. Level the vehicle.

2. Complete the “BEFORE SERVICE PRECAUTION”..

3. Drain the fuel..

4. Using the following procedure:

5. Partially peel back the floor mat as shown in the figure.


6. Remove the service hole cover.


7. Disconnect the following parts:

8. Remove the floor under cover (LH)..

9. Disconnect the HO2S connector.

10. Remove the TWC and HO2S as a single unit..

11. Remove the fuel tank and fuel pump unit as a single unit..

12. Perform the following procedure to verify the fuel tank airtightness.

a. Plug the fuel pump unit pipe, ports B and C.


b. Apply a pressure of 3 kPa {23 mmHg, 0.9 inHg}

to port A and wait for a while.

c. Verify that there is no air flow leakage from the fuel tank.

13. Plug the fuel pump unit pipe and port B.


14. Level the fuel tank.

15. Apply a pressure of 3 kPa {23 mmHg, 0.9 inHg}

to port A and wait for a while.

16. With the pressure still applied, verify that there is air flow from port C and the pressure is 0—3 kPa {0—23 mmHg, 0—0.9 inHg}

.

17. Apply a pressure of -0.5 kPa {-3.8 mmHg, -0.1 inHg}

to port A and wait for a while.

18. With the pressure still applied, verify that there is air flow from port C and the pressure is -0.5—0 kPa {-3.8—0 mmHg, -0.1—0 inHg}

.

19. Apply a pressure to port A and wait for a while.


20. With the pressure still applied, verify that there is no air flow from port C.

AWD

1. Level the vehicle.

2. Complete the “BEFORE SERVICE PRECAUTION”..

3. Drain the fuel..

4. Using the following procedure:

5. Partially peel back the floor mat as shown in the figure.

Main side


Sub side


6. Remove the service hole cover.

Main side


Sub side


7. Disconnect the following parts:

8. Remove the floor under cover..

9. Disconnect the HO2S connector.

10. Remove the TWC and HO2S as a single unit..

11. Remove the propeller shaft..

12. Remove the fuel tank, fuel pump unit and fuel gauge sender unit (sub) as a single unit..

13. Perform the following procedure to verify the fuel tank airtightness.

a. Plug the fuel pump unit pipe, ports B and C.


b. Apply a pressure of 3 kPa {23 mmHg, 0.9 inHg}

to port A and wait for a while.

c. Verify that there is no air flow leakage from the fuel tank.

14. Plug the fuel pump unit pipe and port B.


15. Level the fuel tank.

16. Apply a pressure of 3 kPa {23 mmHg, 0.9 inHg}

to port A and wait for a while.

17. With the pressure still applied, verify that there is air flow from port C and the pressure is 0—3 kPa {0—23 mmHg, 0—0.9 inHg}

.

18. Apply a pressure of -0.5 kPa {-3.8 mmHg, -0.1 inHg}

to port A and wait for a while.

19. With the pressure still applied, verify that there is air flow from port C and the pressure is -0.5—0 kPa {-3.8—0 mmHg, -0.1—0 inHg}

.

20. Apply a pressure to port A and wait for a while.


21. With the pressure still applied, verify that there is no air flow from port C.

Fuel System
Purpose, Outline A multiple hole type fuel injector has been adopted which provides higher fuel injection accuracy for improved fuel efficiency and output. Piston movement-compressio ...

Fuel Tank Removal/Installation
WARNING: Fuel is very flammable liquid. If fuel spills or leaks from the pressurized fuel system, it will cause serious injury or death and facility breakage. Fuel can also irritate skin ...

Other materials:

Room Light Control System
Outline The room light control system changes the illumination condition and illumination level of the interior lights (door position) according to whether the doors are opened/closed and locked/unlocked. The room light control system is controlled by the rear body control modul ...

Air Intake Actuator [Full Auto Air Conditioner]
Purpose The air intake actuator moves the air intake door in the blower unit to switch the air intake port. Function The air intake actuator drives the motor based on the signal from the climate control unit and moves the air intake door to the FRESH or REC position. ...

Selector Lever Inspection
1. Switch the ignition ON (engine off or on). 2. Perform the following procedures to inspect the selector lever. If there is any malfunction, adjust the selector cable.. a. Verify that the selector lever can be operated as shown in the figure. b. Verify that the selector lever ...

© 2016-2022 Copyright www.mcx5.org