Mazda CX-5 Service & Repair Manual: Fuel Filler Pipe Removal/Installation
WARNING:
-
Fuel is very flammable liquid. If fuel spills or leaks from the pressurized fuel system, it will cause serious injury or death and facility breakage. Fuel can also irritate skin and eyes. To prevent this, always complete the “Fuel Line Safety Procedure”, while referring to the “BEFORE SERVICE PRECAUTION”.
-
A person charged with static electricity could cause a fire or explosion, resulting in death or serious injury. Before draining fuel, make sure to discharge static electricity by touching the vehicle body.
CAUTION:
-
Disconnecting/connecting the quick release connector without cleaning it may cause damage to the fuel pipe and quick release connector. Always clean the quick release connector joint area before disconnecting/connecting using a cloth or soft brush, and make sure that it is free of foreign material.
U.S.A. And CANADA
1. Level the vehicle.
2. Complete the “BEFORE SERVICE PRECAUTION”..
3. Drain the fuel..
4. Open the fuel-filler lid.
5. Remove in the order indicated in the table.
|
1 |
Fuel-filler cap |
|
2 |
Dust cover (See Dust cover removal note.) |
|
3 |
Joint hose (See Joint hose installation note.) |
|
4 |
Quick release connector (See QUICK RELEASE CONNECTOR REMOVAL/INSTALLATION [SKYACTIV-G 2.0].) |
|
5 |
Evaporative hose No.1 |
|
6 |
Evaporative hose No.2 |
|
7 |
Plug |
|
8 |
Fuel-filler pipe protector |
|
9 |
Fuel-filler pipe (See Fuel-filler pipe removal note.) |
6. Install in the reverse order of removal.
7. Complete the “AFTER SERVICE PRECAUTION”..
Dust cover removal note
1. Remove the rear mudguard (LH)..
2. Release the dust cover tab using a flathead screwdriver as shown in the figure.
3. Remove the dust cover.
Fuel-filler pipe removal note
1. Remove the rear tire (LH)..
2. Remove the rear parking brake cable installation nut (LH)..
3. Remove the fuel-filler pipe.
Joint hose installation note
1. Install the joint hose as shown in the figure.
Except U.S.A. And CANADA
1. Level the vehicle.
2. Complete the “BEFORE SERVICE PRECAUTION”..
3. Drain the fuel..
4. Open the fuel-filler lid.
5. Remove in the order indicated in the table.
|
1 |
Fuel-filler cap |
|
2 |
Dust cover (See Dust cover removal note.) |
|
3 |
Joint hose (See Joint hose installation note.) |
|
4 |
Breather hose (See Breather hose installation note.) |
|
5 |
Evaporative hose No.1 (See Evaporative hose no.1 installation note.) |
|
6 |
Evaporative hose No.2 |
|
7 |
Plug |
|
8 |
Fuel-filler pipe protector |
|
9 |
Fuel-filler pipe (See Fuel-filler pipe removal note.) |
6. Install in the reverse order of removal.
7. Complete the “AFTER SERVICE PRECAUTION”..
Dust cover removal note
1. Remove the rear mudguard (LH)..
2. Release the dust cover tab using a flathead screwdriver as shown in the figure.
3. Remove the dust cover.
Fuel-filler pipe removal note
1. Remove the rear tire (LH)..
2. Remove the rear parking brake cable installation nut (LH)..
3. Remove the rear crossmember..
4. Remove the fuel-filler pipe.
Evaporative hose no.1 installation note
1. Install the evaporative hose No.1 as shown in the figure.
Breather hose installation note
1. Install the breather hose as shown in the figure.
Joint hose installation note
1. Install the joint hose as shown in the figure.
Fuel Filler Lid Removal/Installation
1. Remove bolts.
2. Remove the fuel-filler lid.
3. Install in the reverse order of removal.
4. Adjust the fuel-filler lid.. ...
Fuel Filter (High Pressure) Removal/Installation
WARNING:
Fuel is very flammable liquid. If fuel spills or leaks from the pressurized
fuel system, it will cause serious injury or death and facility breakage. Fuel
can also irritate skin ...
Other materials:
Start Stop Unit Removal/Installation
CAUTION:
If configuration is not performed when the start stop unit is replaced with
a new one, the vehicle specification information is not stored in the start
stop unit and the system will not operate normally.
When performing configuration, it is necessary to read the vehicl ...
Cowl Upper Plate Installation [Panel Replacement]
Symbol Mark
Installation Procedure
1. When installing new parts, measure and adjust the body as necessary to conform
with standard dimensions.
2. Drill holes for the plug welding before installing the new parts.
3. After temporarily installing new parts, make sure the related parts fit p ...
Compression Inspection
WARNING:
Hot engines and oil can cause severe burns. Be careful not to burn yourself
during removal/installation of each component.
Fuel vapor is hazardous. It can very easily ignite, causing serious injury
and damage. Always keep sparks and flames away from fuel.
Fuel ...
