Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Engine Mount Disassembly/Assembly

Mazda CX-5 Service & Repair Manual / Engine / Engine Assembly / Motor Mounts / Engine Mount Disassembly/Assembly

No.1 Engine Mount (2WD)

1. Remove the front under cover No.2..

2. Remove in the order indicated in the table.

3. Install in the reverse order of removal.



1

No.1 engine mount rubber

(See No.1 engine mount rubber removal note (2WD).)

(See No.1 engine mount installation note (2WD).)

2

Bracket plate (No.1)

(See No.1 engine mount installation note (2WD).)

3

No.1 engine mount bracket

(See No.1 engine mount installation note (2WD).)

4

Bracket plate (No.2)

(See No.1 engine mount installation note (2WD).)


No.1 engine mount rubber removal note (2WD)

1. Loosen the bolts shown in the figure.


NOTE:

2. Remove the No.1 engine mount rubber.

No.1 engine mount installation note (2WD)

1. Install the No.1 engine mount bracket, plate (No.1), and plate (No.2) and temporarily tighten the installation bolts.

2. Tighten the bolt shown in the figure.


3. Install the No.1 engine mount rubber and temporarily tighten the installation bolts.

4. Tighten the No.1 engine mount bracket, plate (No.1) and plate (No.2) installation bolts in the order shown in the figure.


5. Tighten the No.1 engine mount rubber installation bolts.


No.1 Engine Mount (AWD)

NOTE:

1. Remove the front under cover No.1 and front under cover No.2..

2. Set the front mudguard away from the front crossmember and front bumper..


3. Remove the splash shield..

4. Remove in the order indicated in the table.

5. Install in the reverse order of removal.

6. Inspect the front wheel alignment..



1

Bracket plate

(See No.1 engine mount rubber, bracket plate installation note (AWD).)

2

No.1 engine mount rubber

(See No.1 engine mount rubber removal note (AWD).)

(See No.1 engine mount rubber, bracket plate installation note (AWD).)

3

No.1 engine mount bracket

(See No.1 engine mount bracket removal note (AWD).)

(See No.1 engine mount bracket installation note (AWD).)


No.1 engine mount rubber removal note (AWD)

1. Remove the joint bolt (steering gear side) and disconnect the steering shaft from the steering gear and linkage..

2. Disconnect the front crossmember extension.


3. Remove the insulator shown in the figure.


4. Disconnect the hanger rubber from the front crossmember and set it aside.


5. Disconnect the front stabilizer link (front stabilizer side)..

6. Remove the No.1 engine mount rubber installation bolt (front crossmember side).


7. Support the front crossmember component using a jack.


8. Loosen the front crossmember installation bolts (8) and lower the front crossmember component to 15—20 mm {0.60—0.78 in}.


NOTE:

9. Remove the No.1 engine mount rubber.


No.1 engine mount bracket removal note (AWD)

1. Remove the front crossmember component and No.1 engine mount rubber as a single unit..

2. Remove the exhaust manifold..

3. Remove the transfer..

4. Remove the No.1 engine mount bracket.

No.1 engine mount bracket installation note (AWD)

1. Install the No.1 engine mount bracket and tighten the bolts in the order shown in the figure.


2. Install in the reverse order of removal.

No.1 engine mount rubber, bracket plate installation note (AWD)

1. Install the No.1 engine mount rubber to the front crossmember.

2. Tighten the front crossmember installation bolts..

3. Remove the jack.

4. Tighten the No.1 engine mount rubber installation bolts.


5. Install in the reverse order of removal.

No.3 Engine Mount

CAUTION:

1. Disconnect the negative battery cable..

2. Remove the plug hole plate..

3. Remove in the order indicated in the table.

4. Install in the reverse order of removal.



1

No.3 engine mount

(See No.3 engine mount removal note.)

(See No.3 engine mount installation note.)


No.3 engine mount removal note

1. Remove the clips shown in the figure and set the ground cable aside.


2. Remove the front under cover No.2..

CAUTION:

3. Before removing the No.3 engine mount, support the engine (oil pan) using a commercially available engine lifter or garage jack.


4. Place alignment marks on the locations shown in the figure so that they can be assembled to the same positions as before removal.


NOTE:

5. Remove the No.3 engine mount.

No.3 engine mount installation note

NOTE:

1. Tighten the No.3 engine mount stud bolts.


2. Temporarily tighten the No.3 engine mount installation bolts and nuts using the following procedure:

a. Align the alignment marks on the body side and No.3 engine mount, and temporarily tighten the bolts shown in the figure.


b. Temporarily tighten the nuts shown in the figure while aligning the alignment marks of the No.3 engine mount and nuts.


NOTE:

3. Tighten the No.3 engine mount installation bolts and nuts in the order shown in the figure.



No.

Tightening torque

1

76—95 N·m {7.8—9.6 kgf·m, 57—70 ft·lbf}

2

82—95 N·m {8.4—9.6 kgf·m, 61—70 ft·lbf}

3

49—65 N·m {5.0—6.6 kgf·m, 37—47 ft·lbf}


4. Remove the engine lifter or garage jack.

5. Install in the reverse order of removal.

No.4 Engine Mount

CAUTION:

1. Disconnect the negative battery cable..

2. Remove the air cleaner, air hose and fresh air duct as a single unit..

3. Remove the battery tray and PCM component..

4. Remove in the order indicated in the table.

5. Install in the reverse order of removal.



1

No.4 engine mount rubber

(See No.4 engine mount rubber removal note.)

(See No.4 engine mount rubber installation note.)

2

No.4 engine mount bracket

(See No.4 engine mount bracket removal note.)

(See No.4 engine mount bracket installation note.)


No.4 engine mount rubber removal note

1. Remove the clips shown in the figure and set the wiring harness protector aside.


2. Remove the front under cover No.2..

CAUTION:

3. Before removing the No.4 engine mount rubber, support the transaxle using a commercially available engine lifter or garage jack.

4. Remove the No.4 engine mount rubber.

No.4 engine mount bracket removal note

1. Remove the bolt shown in the figure and set the ground cable aside.


2. Place alignment marks on the locations shown in the figure so that they can be assembled to the same positions as before removal.


NOTE:

3. Remove the No.4 engine mount bracket.

No.4 engine mount bracket installation note

NOTE:

1. Tighten the stud bolts for the transaxle.


2. Align the alignment marks on the No.4 engine mount bracket and nuts, and temporarily tighten the nuts shown in the figure.


3. Tighten the No.4 engine mount bracket installation nuts in the order shown in the figure.


4. Install the ground cable to the No.4 engine mount bracket.


No.4 engine mount rubber installation note

1. Install the No.4 engine mount rubber and temporarily tighten the bolts and nut shown in the figure.


2. Tighten the No.4 engine mount rubber installation bolts and nut in the order shown in the figure.



No.

Tightening torque

1, 2

131—153 N·m {14—15 kgf·m, 97—112 ft·lbf}

3

54—62 N·m {5.6—6.3 kgf·m, 40—45 ft·lbf}

4

81—99 N·m {8.3—10 kgf·m, 60—73 ft·lbf}


3. Remove the engine lifter or garage jack.

4. Install in the reverse order of removal.

Motor Mounts
...

Engine Mount
Purpose, Function The engine mount secures the engine and transaxle to the vehicle body, reducing vibration and noise. Construction The three points at the engine front (No.3 en ...

Other materials:

Dynamic Stability Control (DSC)
Outline Electrical brake assist control has been adopted, improving safety. The DSC HU/CM, integrating both the hydraulic unit (HU) and control module (CM), has been adopted, resulting in a size and weight reduction. An enhanced malfunction diagnosis system, used with the M ...

Pressure Control Valve [Skyactiv G 2.0]
U.S.A. And CANADA Purpose, function Prevents fuel tank damage by suppressing the vacuum applied to the fuel tank while the purge solenoid valve is open. Suppresses the vacuum applied from the charcoal canister side to the fuel tank. Construction Integrated with the ...

Rear Wheel Hub Bolt Replacement
1. Remove the brake calliper component and suspend it out of the way using a cable. 2. Remove the disc plate. 3. Remove the wheel hub bolt using the SST as shown in the figure. 4. Place a new wheel hub bolt in the wheel hub. 5. Install the wheel hub by placing a proper sized washer o ...

© 2016-2022 Copyright www.mcx5.org