Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Engine Coolant Replacement

Mazda CX-5 Service & Repair Manual / Engine / Cooling / Engine Coolant Replacement

WARNING:

CAUTION:

  1. Use engine coolant at a concentration that meets the environmental conditions in which the vehicle is driven, otherwise engine damage could occur.

  2. The engine has aluminum parts and must be protected by an ethylene-glycol-based coolant to prevent corrosion and freezing.

  3. Do not use coolants containing Alcohol, Methanol, Borate or Silicate. These coolants could damage the cooling system.

  4. Use only soft (demineralized) water in the coolant mixture. Water that contains minerals will cut down on the coolant's effectiveness.

  5. Engine coolant damages paint. If engine coolant does get on a painted surface, rinse it off quickly.

NOTE:

1. Remove the cooling system cap.

2. Remove the service hole cover (installed to front under cover No.1) used to drain the engine coolant.


3. Loosen the radiator drain plug and drain the engine coolant into a container.


4. Flush the cooling system with water until all traces of color are gone.

5. Let the system drain completely.

6. Tighten the radiator drain plug.

7. Referring to the following chart, select the correct volume percentage of the water and engine coolant. Antifreeze solution mixture percentage (Except FL22 type engine coolant)

Engine coolant protection

Volume percentage (%)

Gravity at 20 °C {68 °F}

Water

Coolant

Above -16 °C {3 °F}

65

35

1.057

Above -26 °C {-15 °F}

55

45

1.072

Above -40 °C {-40 °F}

45

55

1.086


8. Refill the engine coolant from the radiator filler neck until it is close to the top of the radiator filler neck.

9. Refill the engine coolant into the coolant reserve tank up to the F mark on the tank.

10. Install the cooling system cap.

CAUTION:

11. Start the engine and warm up the engine by idling.

12. After the engine warms up, perform the following steps. At this time, be careful of the engine coolant temperature to prevent overheating.

NOTE:

a. Run the engine at 2,500 rpm

for 5 min

.

b. Maintain the engine speed at 3,000 rpm

for 5 s, and then idle

.

c. Repeat steps (1), (2) several times.

13. Stop the engine, and inspect the engine coolant level after the engine coolant temperature decreases. If it is low, repeat steps 8—12.

14. Inspect for engine coolant leakage..

15. Install the service hole cover.

Engine Coolant Protection Inspection
1. Measure the engine coolant temperature and specific gravity using a thermometer and a hydrometer. CAUTION: Use engine coolant at a concentration that meets the environmental conditions ...

Engine Coolant Temperature (ECT) Sensor Inspection
Resistance Inspection WARNING: When the engine is hot, it can badly burn. Turn off the engine and wait until it is cool before removing the ECT sensor. ECT Sensor No.1 1. Remove the ...

Other materials:

Positive Crankcase Ventilation (PCV) Valve Inspection
Airflow Inspection 1. Disconnect the section (A) of ventilation hose shown in the figure. 2. Start the engine and verify that vacuum is applied to the end of the disconnected ventilation hose while the engine is idling. If vacuum is not applied to the ventilation hose, perform the p ...

Light Switch Removal/Installation
NOTE: When removing the light switch, it is necessary to rotate the steering wheel. If the ignition is switched off from ON (engine on) with the driver's door closed, the steering wheel is locked. Therefore, perform the procedure in Steps 1 to 3 so that the steering wheel is not ...

Outer Mirror Glass Installation
1. Connect the mirror heater connectors. (with heated outer mirror) 2. Connect the blind spot monitoring (BSM) warning indicator light connector (with blind spot monitoring system). NOTE: Lightly pull the blind spot monitoring (BSM) warning indicator light connector and verify t ...

© 2016-2024 Copyright www.mcx5.org