Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Cruise Control System

Outline

Component and function

Component

Function

DSC HU/CM

(CAN communication: Vehicle speed signal)

The vehicle speed signal is sent to the PCM from the DSC HU/CM.

Cruise control switch

ON

The cruise control system main switch. The cruise control system goes into standby with the operation of the switch.

OFF

The cruise control system main switch. The cruise control system is turned off with the operation of the switch.

SET (+)

  • If the switch is pressed when the vehicle speed exceeds 25 km/h {16 mph} with the system in standby, the vehicle speed at the point when the switch is pressed is stored in the PCM and the system initiates the cruise control.

  • The PCM controls acceleration by the pressing of the switch (tap-up operation) or when the switch is continuously pressed during cruise control.

SET (?)

  • If the switch is pressed when the vehicle speed exceeds 25 km/h {16 mph} with the system in standby, the vehicle speed at the point when the switch is pressed is stored in the PCM and the system initiates the cruise control.

  • The PCM controls deceleration by the pressing of the switch (tap-down operation) or when the switch is continuously pressed during cruise control.

RESUME

If the switch is pressed when the vehicle speed exceeds 25 km/h {16 mph} with the system in standby and the previous pre-set vehicle speed is stored in the PCM, the system initiates the cruise control so that the vehicle speed is the pre-set vehicle speed stored in the PCM.

CANCEL

If the switch is pressed during cruise control, the cruise control system goes into standby (pre-set vehicle speed is stored).

Brake switch

Depressing the brake pedal during cruise control switches the cruise control system to standby mode (pre-set vehicle speed is stored).

CPP switch (MTX)

Depressing the clutch pedal during cruise control switches the cruise control system to standby mode (pre-set vehicle speed is stored).

Neutral switch (MTX)

Shifting to neutral during cruise control switches the cruise control system to standby mode (pre-set vehicle speed is stored).

TCM (ATX)

(CAN communication: gear signal)

If the following operation is performed during cruise control, the cruise control system goes into standby mode (pre-set vehicle speed is stored).

  • The selector lever is shifted from D position to N position.

DSC HU/CM

(CAN communication: Brake pressure)

If the brake pressure exceeds 0.3 MPa

, the cruise control system goes into standby mode (pre-set vehicle speed is stored).

Parking brake switch

If the parking brake is applied, the cruise control system goes into standby mode (pre-set vehicle speed is stored).

TCM (ATX)

(CAN communication: diagnosis signal)

If there is a malfunction with the AT, the cruise control system goes into standby mode (pre-set vehicle speed is stored).

PCM

The cruise control system is executed or stopped according to the cruise control switch signals. The throttle valve actuator is operated so that the vehicle speed is the pre-set vehicle speed during cruise control system.

Throttle valve actuator

The duty signal sent from the PCM adjusts the throttle valve opening angle.

Cruise main indicator light (Amber)

(See CRUISE MAIN INDICATOR LIGHT (AMBER) [SKYACTIV-G 2.0].)

Cruise set indicator light (Green)

(See CRUISE SET INDICATOR LIGHT (GREEN) [SKYACTIV-G 2.0].)


Structural View


Block Diagram


Cruise Control Switch Inspection
1. Disconnect the negative battery cable and wait for 1 min or more.. 2. Remove the driver?side air bag module.. 3. Disconnect the clock spring connector (part wiring harness-side). 4. Measure ...

Cruise Main Indicator Light (Amber)
Purpose/Function Illuminates while the cruise control system is in standby mode to inform the driver that the cruise control system is on standby. Construction Built into the in ...

Other materials:

Instrument Cluster
Outline The instrument cluster centrally controls the speedometer, tachometer, odometer/tachometer, fuel gauge, warning/indicator lights, trip computer, warning sounds and panel lights. Function The instrument cluster displays the following information to notify the user ...

Fuel Gauge Sender Unit Removal/Installation [Awd]
WARNING: Always keep sparks and flames away from fuel when servicing the fuel system. Fuel can be easily ignited which could cause serious injury or death, and damage to equipment. Fuel line spills and leakage from the pressurized fuel system are dangerous. Fuel can ignite a ...

Fuel Filler Lid Opener And Lever Removal/Installation
Fuel-filler Lid Opener 1. Open the fuel-filler lid. 2. Remove the nut. 3. Remove the service hole cover on the trunk side trim. 4. While pressing the tabs of the stopper bracket in the direction of arrow (1) shown in the figure, press it in the direction of arrow (2) to detach it fr ...

© 2016-2025 Copyright www.mcx5.org