Mazda CX-5 Service & Repair Manual: Construction Standard Values [Construction Standard Values]
Front view
|
No. |
Measurement part |
Standard values (mm {in}) |
Maximum values (mm {in}) |
Minimum values (mm {in}) |
Side by difference (mm {in}) |
|
A |
1 |
5.0 {0.20} |
7.0 {0.27} |
3.0 {0.12} |
2.0 {0.079} |
|
B |
2 |
4.5 {0.18} |
6.0 {0.24} |
3.0 {0.12} |
- |
|
C |
3 |
4.5 {0.18} |
6.4 {0.25} |
2.6 {0.10} |
2.5 {0.098} |
|
4 |
1.0 {0.039} |
2.8 {0.11} |
-0.8 {-0.03} |
- |
|
|
D |
5 |
1.8 {0.055} |
3.2 {0.13} |
0.4 {0.002} |
1.4 {0.055} |
|
E |
6 |
3.7 {0.15} |
4.9 {0.19} |
2.5 {0.098} |
1.2 {0.047} |
|
F |
7 |
0.5 {0.02} |
1.8 {0.071} |
- |
- |
|
8 |
0.5 {0.02} |
1.2 {0.047} |
0.2 {0.008} |
- |
|
|
G |
9 |
0 |
1.6 {0.063} |
-1.6 {-0.063} |
- |
|
10 |
0 |
1.6 {0.063} |
-1.6 {-0.063} |
- |
|
|
11 |
0 |
1.5 {0.059} |
-1.5 {-0.059} |
- |
|
|
H |
12 |
3.5 {0.14} |
4.5 {0.18} |
2.5 {0.098} |
1.0 {0.039} |
|
13 |
0 |
1.0 {0.039} |
-1.0 {-0.039} |
- |
Rear view
|
No. |
Measurement part |
Standard values (mm {in}) |
Maximum values (mm {in}) |
Minimum values (mm {in}) |
Side by difference (mm {in}) |
|
A |
1 |
6.0 {0.24} |
7.0 {0.28} |
5.0 {0.20} |
1.2 {0.047} |
|
2 |
-1.0 {-0.039} |
0 |
-2.0 {-0.079} |
- |
|
|
B |
3 |
4.3 {0.17} |
6.8 {0.27} |
1.8 {0.071} |
2.5 {0.047} |
|
C |
4 |
1.8 {0.071} |
3.0 {0.12} |
0.6 {0.02} |
- |
|
D |
5 |
1.8 {0.071} |
3.3 {0.13} |
0.3 {0.01} |
- |
|
E |
6 |
4.5 {0.18} |
6.5 {0.26} |
2.5 {0.098} |
1.5 {0.059} |
|
7 |
0 |
1.8 {0.071} |
-1.8 {-0.071} |
- |
|
|
F |
8 |
4.0 {0.16} |
6.5 {0.26} |
1.5 {0.059} |
2.5 {0.098} |
|
G |
9 |
6.0 {0.24} |
8.0 {0.31} |
4.0 {0.16} |
2.0 {0.079} |
|
H |
10 |
0.5 {0.02} |
1.8 {0.071} |
- |
- |
|
11 |
0.5 {0.02} |
1.5 {0.059} |
-0.2 {-0.008} |
- |
|
|
I |
12 |
3.5 {0.14} |
4.5 {0.18} |
2.5 {0.098} |
1.0 {0.039} |
|
13 |
0 |
1.0 {0.039} |
-1.0 {-0.039} |
- |
|
|
J |
14 |
3.5 {0.14} |
4.5 {0.18} |
2.5 {0.098} |
1.0 {0.039} |
|
15 |
0 |
1.0 {0.039} |
-1.0 {-0.039} |
- |
Center Pillar Removal [Panel Replacement]
Symbol Mark
Removal Procedure
CAUTION:
Remove the curtain air bag module to prevent damage before servicing.
Front-side
Rear-side
CAUTION:
Avoid cutting with a bl ...
Corner Plate Installation [Panel Replacement]
Symbol Mark
Installation Procedure
1. When installing new parts, measure and adjust the body as necessary to conform
with standard dimensions.
2. Drill holes for the plug welding before inst ...
Other materials:
Air Fuel Ratio (A/F) Sensor Heater Control [Skyactiv G 2.0]
Outline
Based on the control of the A/F sensor heater, a stabilized oxygen concentration
is detected even at low exhaust temperatures, and feedback control of fuel injection
even at cold engine start is made possible for improved cold temperature exhaust
emission performance.
...
Air Intake Actuator Inspection [Manual Air Conditioner]
1. Connect battery positive voltage to air intake actuator terminal B (or C),
connect terminal C (or B) to ground, and then verify that the air intake actuator
operates as shown in the table.
If the operation condition is not normal, replace the air intake actuator.
...
Differential Oil Replacement
1. Place the vehicle on level ground.
2. Remove the filler plug.
3. Remove the drain plug and drain the differential oil into a container.
4. Install a new washer and the drain plug, and tighten.
Tightening torque
40—53 N·m {4.1—5.4 kgf·m, 30—39 ft·lbf}
5. Add the ...
