Mazda CX-5 Service & Repair Manual: Climate Control Unit Inspection [Manual Air Conditioner]
1. Remove the climate control unit with the connector connected..
2. Switch the ignition ON (engine off or on).
3. Connect the negative (-) lead of the tester to the body ground.
4. By inserting the positive (+) lead of the tester into the climate control unit connector, measure the voltage according to the terminal voltage table.
-
If there is any malfunction, inspect the parts under “Inspection item(s)”.
-
If the parts under “Inspection item(s)” are normal, replace the climate control unit.
Terminal Voltage Table (Reference)
|
Terminal |
Signal name |
Connected to |
Measurement condition |
Voltage (V) |
Inspection item(s) |
|
A |
TNS signal |
Front body control module (FBCM) |
TNS OFF |
1.0 or less |
|
|
TNS ON |
B+ |
||||
|
B |
Illumination (-) |
Instrument cluster |
Headlight ON and panel light control MAX |
2.0 |
|
|
Headlight ON and panel light control MIN |
9.65 |
||||
|
C |
Motor operation |
Air intake actuator |
Switched to RECIRCULATE |
B+ |
|
|
Switched to FRESH |
1.0 or less |
||||
|
D |
Ground |
Body ground |
Under any condition |
1.0 or less |
|
|
E |
Motor operation |
Air intake actuator |
Switched to RECIRCULATE |
1.0 or less |
|
|
Switched to FRESH |
B+ |
||||
|
F |
Sensor GND |
Evaporator temperature sensor |
Under any condition |
1.0 or less |
|
|
G |
Blower fan ON/OFF signal |
Fan switch |
Fan stopped |
B+ |
|
|
Fan on |
1.0 or less |
||||
|
H |
Evaporator temperature sensor input |
Evaporator temperature sensor |
Compared with temperature detected by evaporator temperature sensor |
Refer to graph 1 |
|
|
I |
Blower fan position signal |
Fan switch |
3rd, 4th |
1.0 or less |
|
|
off, 1st, 2nd |
B+ |
||||
|
J |
B+ |
ROOM 15 A fuse |
Under any condition |
B+ |
|
|
K |
LIN |
Front body control module (FBCM) |
Because this terminal is for communication, good/no good judgment by terminal voltage is not possible. |
|
|
|
L |
IG2 |
Front body control module (FBCM) |
Switch the ignition to ON |
B+ |
|
|
Switch the ignition off |
1.0 or less |
||||
Climate Control Unit Inspection [Full Auto Air Conditioner]
1. Remove the climate control unit with the connector connected..
2. Switch the ignition ON (engine off or on).
3. Connect the negative (-) lead of the tester to body ground.
4. By inserting the ...
Climate Control Unit Removal/Installation [Full Auto Air Conditioner]
NOTE:
The climate control unit prior to replacement stores the vehicle specification
information.
The new climate control unit does not store any vehicle specification information.
...
Other materials:
Winter Driving
Carry emergency gear, including tire chains, window scraper, flares, a small
shovel, jumper cables, and a small bag of sand or salt.
Ask an Authorized Mazda Dealer to perform the following precautions: l Have the
proper ratio of antifreeze in the radiator.
• Inspect the battery and its cable ...
Magnet Clutch [Manual Air Conditioner]
Purpose
The magnetic clutch transmits the rotation force from the engine to the shaft
in the A/C compressor.
Function
The magnetic clutch engages or disengages the magnetic clutch and the A/C
turns on or off by switching the power transmission from the engine.
Con ...
Oil Seal (Differential) Replacement [C66 M R]
1. Remove the front under cover No.2..
2. Drain the manual transaxle oil..
3. Disconnect the drive shaft (LH) from the MTX..
4. Disconnect the drive shaft (RH) from the MTX..
5. Remove the oil seal (LH).
6. Remove the oil seal (RH).
7. Using the SSTs and a hammer, tap a new oil s ...
