Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Car Navigation System Does Not Start Operation [Car Navigation System]

Mazda CX-5 Service & Repair Manual / Accessories / Electronics / Navigation / Car Navigation System Does Not Start Operation [Car Navigation System]


Possible DTC

Even if the NAVI mode is selected, the car-navigation system screen does not display.

POSSIBLE CAUSE

  • NAV switch malfunction

  • Power supply fuse (+B, ACC) burnt out

  • Open or short circuit in power supply (+B, ACC, GND) wiring harness

  • Open or short circuit in power supply (+B, ACC, GND) wiring harness

  • Open or short circuit in wiring harness between audio unit and car-navigation unit communication system

  • Car-navigation unit malfunction

  • Audio unit malfunction


Diagnostic Procedure


Step

Inspection

Action

1

    VERIFY MALFUNCTION SYMPTOM

  • Switch the ignition ON (engine off or on).

  • Turn the audio unit power supply on and select the NAVI mode.

  • Does the car-navigation system launch and the map screen display?

Yes

Go to Step 6.

No

Go to the next step.

2

    DETERMINE IF MALFUNCTION CAUSE IS SWITCH

  • Operate switches other than the NAV switch.

  • Do the modes other than the NAVI mode switch normally?

Yes

Go to the next step.

No

Inspect the switch referring to the switch inspection procedure of the diagnostic assist function.

(See DIAGNOSTIC ASSIST FUNCTION [AUDIO].)

3

    INSPECT CAR-NAVIGATION UNIT POWER SUPPLY

  • Switch the ignition to ACC.

  • Measure the voltage at the following terminals:

    • Terminal 1H (+B)

    • Terminal 1G (ACC)

  • Is the voltage value the battery voltage?

Yes

Go to the next step.

No

  • Inspect the AUDIO1 15 A or AUDIO2 7.5 A fuse.

    If the fuse is burned out:

  • Inspect for a short to ground in the wiring harness between the AUDIO1 15A fuse and car- navigation unit terminal 1H, or the AUDIO2 7.5 A fuse and car-navigation unit terminal 1G, and perform repairs.

    If the fuse is not damaged or burned out:

  • Inspect for an open circuit in the wiring harness between the battery and car-navigation unit terminal 1H or 1G.

4

    INSPECT CAR-NAVIGATION UNIT GROUND

  • Switch the ignition off (LOCK).

  • Disconnect the audio unit connector.

  • Verify the continuity between ground and the following terminal connectors 1A, 1B, 1C, and 1D on the wiring harness side.

  • Is there continuity?

Yes

Go to the next step.

No

Inspect and repair the ground point for looseness, disengagement, or lifting. Inspect and repair the wiring harness for an open circuit.

5

    INSPECT CAR-NAVIGATION UNIT COMMUNICATION

  • Switch the ignition off (LOCK).

  • Disconnect the audio unit connector.

  • Inspect for malfunction between the following wiring harnesses.

    • Audio unit terminal 5A and car-navigation unit terminal 2A

    • Audio unit terminal 5B and car-navigation unit terminal 2B

    • Audio unit terminal 5C and car-navigation unit terminal 2C

    • Audio unit terminal 5D and car-navigation unit terminal 2D

  • Is any malfunction verified?

Yes

Inspect and repair the wiring harness.

No

Go to the next step.

6

    DETERMINE IF MALFUNCTION CAUSE IS car-navigation UNIT

  • Switch the ignition ON (engine off or on).

  • Launch the audio unit diagnostic assist function.

    (See DIAGNOSTIC ASSIST FUNCTION [AUDIO].)

  • Select diagnostic assist code 16 external device connection information clearing.

  • Switch the ignition off (LOCK).

  • Switch the ignition ON (engine off or on).

  • Launch the audio unit diagnostic assist function.

    (See DIAGNOSTIC ASSIST FUNCTION [AUDIO].)

  • Select diagnostic assist code 15 vehicle NAVI signal verification.

  • Is NAVI (USB) NG displayed?

Yes

Replace the car-navigation unit.

(See CAR-NAVIGATION UNIT REMOVAL/INSTALLATION.)

No

Replace the audio unit.

(See AUDIO UNIT REMOVAL/INSTALLATION.)


Car Navigation System Does Not Operation [Car Navigation System]
Possible DTC Even if the map screen is touched, the car-navigation system cannot be operated POSSIBLE CAUSE Audio unit malf ...

Car Navigation Unit
Purpose Reads the SD card data inserted into the car-navigation unit and sends the read data to the audio unit. Function The car-navigation unit has the following functions: ...

Other materials:

Audio Unit Removal/Installation
Removal 1. Disconnect the negative battery cable. 2. Remove the decoration panel.. 3. Remove the bolt. 4. Remove the screws. NOTE: When removing the audio unit, the audio unit could interfere with the climate control unit and scratch the climate control unit. Perform the serv ...

When Liftgate Cannot be Opened
When Liftgate Cannot be Opened If the vehicle battery is dead or there is a malfunction in the electrical system and the liftgate can not be opened, perform the following procedure as an emergency measure to Open it: 1. Remove the cap on the interior surface of the liftgate with a flathead sc ...

Crankshaft, Main Bearing
Purpose, Function The crankshaft converts the reciprocating movement of the piston to a rotational movement via the connecting rod. The main bearing forms an oil film on the outer surface of the crankshaft journal to prevent wear due to sliding. Construction Crankshaft ...

© 2016-2024 Copyright www.mcx5.org