Chevrolet Spark manuals

Mazda CX-5 Service & Repair Manual: Bsm Indicator Light Flashes While Not Under Bsm Indicator Light Flashing Conditions (No Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]

Mazda CX-5 Service & Repair Manual / Accessories / Safety Systems / Bsm Indicator Light Flashes While Not Under Bsm Indicator Light Flashing Conditions (No Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]


Description

BSM indicator light flashes while not under BSM indicator light-flashing conditions (no combination switch operation (turn signal switch)

  • The BSM indicator light flashes despite not satisfying the BSM indicator light flashing conditions (vehicle speed above 32 km/h {20 mph} or more, turn signal on, and vehicle in warning zone).

  • The BSM indicator light flashes, but the turn signals are off.

Possible Causes

NOTE:

  • This malfunction symptom is basically the same as symptom “BSM indicator light while not under BSM indicator light-illumination conditions”.

  • BSM control module recognizes a vehicle as being inside the warning zone when it is actually outside of it.

    • Radar (BSM control module integrated) is emitted outside of warning zone (deviates from warning zone)

      • Damage, deformity or looseness to installation bracket or vehicle frame (including moderate impacts).

      • Malfunction in steering angle signal (communication error between rear body control module (RBCM) and BSM control module, or EPS control module malfunction).

      • Problem with rear bumper such as soiling to radar emitting/receiving area, application of stickers (including transparent types), repairs using putty application.

    • After-market electrical parts interfere with BSM system

  • BSM does not recognize vehicle speed correctly (BSM control module mistakenly recognizes vehicle speed as being above 32 km/h {20 mph} or more)

    • PCM communication error with BSM control module

    • Malfunction in ABS wheel speed sensor related parts

  • BSM control module mistakenly recognizes that turn signals have been operated

    • Short to ground circuit in wiring harness between combination switch (turn signal switch) and rear body control module (RBCM)

    • Communication error between rear body control module (RBCM) and BSM control module

    • BSM control module malfunction


Diagnostic Procedure

Step

Inspection

Result

Action

1

    VERIFY MALFUNCTION SYMPTOM

  • BSM indicator light illuminates while under light-off conditions.

Yes

Go to the symptom troubleshooting procedure, “ BSM indicator light illuminates while not under BSM indicator light-off conditions”.

(See BSM INDICATOR LIGHT ILLUMINATES WHILE NOT UNDER LIGHT-ILLUMINATION CONDITIONS [BLIND SPOT MONITORING (BSM)].)

No

Go to the next step.

2

    INSPECT IF MALFUNCTION IS IN REAR BODY CONTROL MODULE (RBCM) INPUT SIGNAL OR BSM

  • Monitor the following PIDs on the suspected side of the BSM control module using the M-MDS.

    (See PID/DATA MONITOR TABLE [BLIND SPOT MONITORING (BSM)].)

    • TURN_SW_L

    • TURN_SW_R

  • Are the monitoring values normal?

Yes

Replace the BSM control module.

(See BLIND SPOT MONITORING (BSM) CONTROL MODULE REMOVAL/INSTALLATION.)

No

Retrieve DTCs from the start stop unit, instrument cluster, and BSM control module using the M-MDS.

(See DTC INSPECTION [START STOP UNIT].)

(See DTC INSPECTION [INSTRUMENT CLUSTER].)

(See DTC INSPECTION [BLIND SPOT MONITORING (BSM)].)


Bsm Indicator Light Does Not Flash While Under Bsm Indicator Light Flashing Conditions (With Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
Description BSM indicator light does not flash while under BSM indicator light-flashing conditions (with combination switch operation (turn signal switch)) ...

PID/Data Monitor Inspection [Blind Spot Monitoring (Bsm)]
1. Connect the M-MDS to the DLC-2. 2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS. a. Select “DataLogger”. b. Select “Modules ...

Other materials:

Low Fuel Warning Light
Purpose The low fuel warning light warns the driver that the remaining fuel level is low. Function The instrument cluster calculates the fuel quantity based on the following CAN signals, and if a remaining fuel amount of approx. 10 L {2.6 US gal, 2.2 Imp gal} (fuel gauge ...

Slide Motor Inspection
WARNING: Handling a side air bag improperly can accidentally operate (deploy) the air bag, which may seriously injure you. Read the service warnings/cautions in the Workshop Manual before handling the front seat (side air bag integrated).. CAUTION: When performing the pro ...

Awd Control Module Inspection
NOTE: AWD CM terminal voltage can vary depending on measuring conditions and vehicle aging, resulting in misdiagnosis. Therefore, it is necessary to perform an overall inspection of the input/output systems and AWD CM to determine which part is malfunctioning. With the AWD C ...

© 2016-2022 Copyright www.mcx5.org