Mazda CX-5 Service & Repair Manual: Brakes
- General
- 2 6 Brake [Fw6 A EL, Fw6 Ax EL]
- Brake Fluid Air Bleeding
- Brake Fluid Inspection
- Brake Fluid Pressure Sensor
- Brake Fluid Pressure Sensor Inspection
- Brake Hose (Front) Removal/Installation
- Brake Hose (Rear) Removal/Installation
- Brake Pedal
- Brake Pedal Inspection
- Brake Pedal Removal/Installation
- Brake/Taillight Bulb Removal/Installation
- Brakes
- Brakes SST
- Conventional Brake System
- Disc Pad (Front) Replacement
- Disc Pad (Rear) Replacement
- General Procedures (Brake)
- Low And Reverse Brake [Fw6 A EL, Fw6 Ax EL]
- Master Cylinder
- Master Cylinder
- Master Cylinder Removal/Installation
- Power Brake Unit
- Power Brake Unit Inspection
- Power Brake Unit Removal/Installation
- R 3 5 Brake [Fw6 A EL, Fw6 Ax EL]
- Vacuum Hose Removal/Installation
- Vacuum Line Inspection
- Vacuum Pump Inspection
- Vacuum Pump Removal/Installation
- Vacuum Pump [Skyactiv G 2.0]
- Brake Control, Vehicle Dynamics
- General Information
- ABS
- Sensors, Switches, Relays
- Disc Brakes
- Caliper (Front) Disassembly/Assembly
- Caliper (Rear) Disassembly/Assembly
- Front Brake (Disc)
- Front Brake (Disc) Inspection
- Front Brake (Disc) Removal/Installation
- Rear Brake (Disc)
- Rear Brake (Disc) Inspection
- Rear Brake (Disc) Removal/Installation
- Parking Brake
- Front Parking Brake Cable Removal/Installation
- Parking Brake Lever Adjustment
- Parking Brake Lever Inspection
- Parking Brake Lever Removal/Installation
- Parking Brake System
- Rear Parking Brake Cable Removal/Installation
- Parking Brake Switch Inspection
- Sensors, Switches, Relays
- Brake Fluid Level Sensor Inspection
- Brake Switch Inspection
- Turbine/Input Shaft Speed Sensor, Output Shaft Speed Sensor [Fw6 A EL, Fw6 Ax
EL]
1. Disconnect the negative battery cable..
2. Spread open the rain sensor cover in the direction of the arrows (1) and disengage
tabs A to remove it.
3. Disconnect the rain sensor connector ...
Other materials:
Heated Oxygen Sensor (HO2 S) Inspection
HO2S Inspection
1. Connect the M-MDS to the DLC?2.
2. Switch the ignition ON (engine on).
3. Warm up the engine to normal operating temperature.
4. Access the following PIDs using the M-MDS..
VSS (Vehicle speed)
RPM (Engine speed)
O2S12 (HO2S output voltage)
5. D ...
PID/Data Monitor Inspection [Two Step Deployment Control System]
1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initialization
screen of the M-MDS.
a. Select “DataLogger”.
b. Select “Modules”.
c. Select “RCM”.
3. Select the applicable PID from the PID table.
4. Verify the PID da ...
Hood Latch Switch Inspection
1. Disconnect the negative battery cable..
2. Remove the front bumper..
3. Disconnect the hood latch switch connector..
4. Verify that the continuity is as indicated in the table.
NOTE:
Inspect the continuity when the hood is open and closed.
If the operation as i ...
© 2016-2026 Copyright www.mcx5.org
