Mazda CX-5 Service & Repair Manual: Blind Spot Monitoring (Bsm) Control Module Inspection
1. Disconnect the negative battery cable..
2. Remove the rear combination light..
3. Remove the rear bumper..
4. Connect the negative battery cable..
5. Verify that the voltages of each of the terminals are as indicated in the terminal voltage table (reference).
-
If the voltage is not as specified in the terminal voltage table (reference), inspect the parts under Inspection item(s).
-
If the system does not operate normally even though the inspection items are normal, replace the BSM control module (RH) or BSM control module (LH).
Terminal Voltage Table (Reference)
BSM control module (RH)
|
Terminal |
Signal name |
Connected to |
Measurement conditions |
Voltage (V) |
Inspection item(s) |
|
|
A |
Ground |
Body ground |
Under any condition |
1.0 or less |
|
|
|
B |
Power position (IG1) |
IG relay |
Ignition switched ON (Engine off or on) |
B+ |
|
|
|
Ignition switched off (LOCK) or ACC |
1.0 or less |
|||||
|
C |
— |
— |
— |
— |
— |
|
|
D |
BSM indicator light (RH) signal |
BSM indicator light (RH) |
Turn off BSM indicator light using BSM system simulation WRN_IND_R |
1.0 or less |
|
|
|
Turn on BSM indicator light using rear vehicle monitoring system simulation WRN_IND_R |
B+ |
|||||
|
E |
— |
— |
— |
— |
— |
|
|
F |
— |
— |
— |
— |
— |
|
|
G |
MS-CAN_L |
Related module |
Because this terminal is for communication, determination using terminal voltage inspection is not possible. |
|||
|
H |
MS-CAN_H |
Related module |
Because this terminal is for communication, determination using terminal voltage inspection is not possible. |
|||
BSM control module (LH)
|
Terminal |
Signal name |
Connected to |
Measurement conditions |
Voltage (V) |
Inspection item(s) |
|
|
A |
Ground |
Body ground |
Under any condition |
1.0 or less |
|
|
|
B |
Power position (1G1) |
IG relay |
Ignition switched ON (engine off or on) |
B+ |
|
|
|
Ignition switched off (LOCK) or ACC |
1.0 or less |
|||||
|
C |
— |
— |
— |
— |
— |
|
|
D |
BSM indicator light (LH) signal |
BSM indicator light (LH) |
Turn off BSM indicator light using BSM system simulation WRN_IND_L |
1.0 or less |
|
|
|
Turn on BSM indicator light using rear vehicle monitoring system simulation WRN_IND_L |
B+ |
|||||
|
E |
Ground |
Body ground |
Under any condition |
1.0 or less |
|
|
|
F |
— |
— |
— |
— |
— |
|
|
G |
MS-CAN_L |
Related module |
Because this terminal is for communication, determination using terminal voltage inspection is not possible. |
|||
|
H |
MS-CAN_H |
Related module |
Because this terminal is for communication, determination using terminal voltage inspection is not possible. |
|||
Blind Spot Monitoring (Bsm) Control Module
Purpose
Controls the blind spot monitoring (BSM) system.
Function
The BSM control module emits microwaves to detect an oncoming vehicle's position
and speed information via ...
Blind Spot Monitoring (Bsm) Control Module Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the rear combination light..
3. Remove the rear bumper..
4. Disconnect the connector.
5. Remove the nuts.
6. Remove the BSM control m ...
Other materials:
Dynamic Stability Control (DSC)
The Dynamic Stability Control (DSC) automatically controls braking and engine
torque in conjunction with systems such as ABS and TCS to help control side slip
when driving on slippery surfaces, or during sudden or evasive maneuvering, enhancing
vehicle safety.
Refer to ABS and TCS .
DS ...
Rear Brake (Disc) Inspection
Brake Judder Repair Hints
Description
1. Brake judder concern has the following 3 characteristics:
Steering wheel vibration
1. The steering wheel vibrates in the rotation direction. This characteristic
is most noticeable when applying brakes at a vehicle speed of 100—140 km/h {62.2—86.9
...
Rear Drive Shaft
Purpose, Function
Engine noise and vibration have been reduced due to adoption of a bell joint
on the wheel side of the constant velocity joint.
A low noise and vibration double offset joint with low slide resistance has
been adopted for the differential side of the constant v ...
