Chevrolet Spark manuals

Mazda CX-5 Owners Manual: AWD

All-Wheel Drive (AWD) Operation

AWD provides excellent drivability on snow-covered and ice-packed roads, sand and mud, as well as on steep slopes and other slippery surfaces.

A system malfunction or operation conditions are indicated by a warning.

Refer to Warning/Indicator Lights on .

WARNING

Never spin a wheel that is off the ground:

Spinning a wheel that is off the ground as a result of the vehicle being stuck or in a ditch is dangerous. The drive assembly could be seriously damaged which could lead to an accident or could even lead to overheating, oil leakage, and a fire.

AWD Driving

WARNING

Avoid sharp turns, excessive speed and abrupt maneuvers when driving this vehicle:

Sharp turns, excessive speed and abrupt maneuvering of this vehicle is dangerous as it could result in the increased risk of loss of vehicle control, vehicle roll-over, personal injury or death.

This vehicle has a higher center of gravity. Vehicles with a higher center of gravity such as utility and AWD vehicles handle differently than vehicles with a lower center of gravity.

Utility and AWD vehicles are not designed for cornering at high speeds any more than low profile sports cars are designed to perform satisfactorily under off-road conditions. In addition, utility vehicles have a significantly higher rollover rate than other types of vehicles.

Drive carefully when the vehicle is loaded by lowering vehicle speed and applying the brakes earlier:

Abrupt maneuvering and sudden braking when driving a loaded vehicle is dangerous as the driving behavior of a vehicle with a high center of gravity is different when it is loaded compared to when it is not, and could result in the loss of vehicle control and an accident.

Tires and Tire Chains

The condition of the tires plays a large role in the performance of the vehicle.

Moreover, to prevent adverse effects to the drive assembly, please note the following:

Tires

When replacing tires, always replace all front and rear tires at the same time.

All tires must be of the same size, manufacture, brand and tread pattern.

Pay particular attention when equipping snow or other types of winter tires.

Do not mix tread-worn tires with normal tires.

Inspect tire inflation pressures at the specified periods and adjust to the specified pressures.

NOTE

Check the tire inflation pressure label attached to driver's door frame for the correct tire inflation pressure.

Make sure to equip the vehicle with genuine wheels of the specified size, on all wheels. With AWD, the system is calibrated for all four wheels being of the same dimensions.

Tire chains

Install tire chains to the front tires.

Do not use tire chains on the rear wheels.

Do not drive the vehicle faster than 30 km/h (19 mph) with the tire chains installed.

Do not drive the vehicle with tire chains on road conditions other than snow or ice.

Towing

If the vehicle requires towing, have it towed with all four wheels completely off the ground.

Dynamic Stability Control (DSC)
The Dynamic Stability Control (DSC) automatically controls braking and engine torque in conjunction with systems such as ABS and TCS to help control side slip when driving on slippery surfaces, or ...

Power Steering
Power Steering • Power steering is only operable when the engine is running. If the engine is off or if the power steering system is inoperable, you can still steer, but it requires more physic ...

Other materials:

Units
Electric current A (ampere) Electric power W (watt) Electric resistance ohm Electric voltage V (volt) Length mm (millimeter) in (inch) ...

Brake Switch Inspection
CAUTION: Inspect the brake switch with it installed to the brake pedal, otherwise the brake switch may not operate normally. If the brake switch is removed from the brake pedal, replace the brake switch with a new one. 1. Remove the lower panel.. 2. Remove the front heat duct ( ...

Rear Side Frame Installation [Panel Replacement]
Symbol Mark Installation Procedure 1. When installing new parts, measure and adjust the body as necessary to conform with standard dimensions. 2. Drill holes for the plug welding before installing the new parts. 3. After temporarily installing new parts, make sure the related parts fit p ...

© 2016-2024 Copyright www.mcx5.org