Mazda CX-5 Service & Repair Manual: A/C Unit Disassembly/Assembly
1. Disassemble in the order indicated in the table.
CAUTION:
-
If a non-specified grease is used, it may result in abnormal noise or improper operation of the links. Apply only the specified grease to each link.
2. Assemble in the reverse order of disassembly.
|
Step |
Part name |
Disassembly/assembly of main parts |
||
|
Heater core |
Evaporator temperature sensor |
Evaporator |
||
|
1 |
Polyurethane foam |
? |
? |
? |
|
2 |
Expansion valve |
? |
? |
? |
|
3 |
Adhesive polyurethane |
? |
? |
? |
|
4 |
Drain hose |
? |
? |
? |
|
5 |
Plate (1) |
X |
? |
? |
|
6 |
Plate (2) |
X |
? |
? |
|
7 |
Heater core |
X |
? |
? |
|
8 |
Driver-side air mix actuator (Full-auto air conditioner) |
? |
? |
? |
|
9 |
Driver-side air mix link (Full-auto air conditioner) |
? |
? |
? |
|
10 |
Passenger-side air mix actuator (Full-auto air conditioner) |
? |
? |
? |
|
11 |
Passenger-side air mix link (Full-auto air conditioner) |
? |
? |
? |
|
12 |
Air mix link (Manual air conditioner) |
? |
? |
? |
|
13 |
Airflow mode actuator (Full-auto air conditioner) |
? |
? |
? |
|
14 |
Airflow mode link set |
? |
? |
? |
|
15 |
Power MOS FET (Full-auto air conditioner) |
? |
? |
? |
|
Resistor (Manual air conditioner) |
? |
? |
? |
|
|
16 |
A/C case (1) |
? |
X |
X |
|
17 |
A/C case (2) |
? |
X |
X |
|
18 |
Evaporator temperature sensor. |
? |
X |
X |
|
19 |
Evaporator |
? |
? |
X |
|
20 |
A/C case (3) |
? |
? |
? |
|
21 |
A/C case (4) |
? |
? |
? |
|
22 |
Door damper |
? |
? |
? |
X: Applicable
?: Not applicable
Evaporator Temperature Sensor Assembly Note
1. Assemble the evaporator temperature sensor as shown in the figure.
CAUTION:
-
When installing the evaporator temperature sensor without replacing the evaporator, assemble the evaporator temperature sensor with the installation position slid to the left of the previous position by 1 line. If the evaporator temperature sensor is assembled to the previously installed position, it may not function due to poor contact of the fin surface with the sensor detection area caused by fin deformation.
NOTE:
-
If an evaporator temperature sensor cannot be correctly positioned on the evaporator, replace the evaporator.
A/C Unit
Outline
The A/C unit which integrates the cooling and heater units has been adopted.
Construction
The A/C unit consists of the following parts.
Operation
Air Mix Door Op ...
A/C Unit Removal/Installation
1. Disconnect the negative battery cable..
2. Discharge the refrigerant..
3. Drain the engine coolant..
CAUTION:
If moisture or foreign material enters the refrigeration cycle, cooling a ...
Other materials:
D Pillar Trim Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Trunk board.
b. Trunk end trim.
c. Rear scuff plate.
d. Trunk side trim.
3. Take the shaded area shown in the figure, and remove the D-pillar trim in
the direction of the arrow in the order of (1), (2), (3) wh ...
Electric Power Steering (Eps) Motor
Purpose, Function
The EPS motor is driven by the control current from the EPS CM (control module)
and generates assist torque to manual steering mechanism.
Construction
The EPS motor is installed to the steering column with an integrated EPS
CM.
The EPS motor is a b ...
Air Bag System Service Cautions [Standard Deployment Control System]
Air Bag System Component Disassembly
Disassembling the air bag system components could cause it to not operate
(deploy) normally. Never disassemble any air bag system components.
Air Bag Module, Pre-tensioner Seat Belt Handling
Oil, grease, or water on the air bag modules ...
