Mazda CX-5 Service & Repair Manual: A/C Cut Off Control [Skyactiv G 2.0]
Outline
-
Controls the A/C operation by switching the A/C relay ON/OFF at the optimal timing according to engine operation conditions. Acceleration performance and A/C compressor reliability have been improved by controlling the A/C operation.
Block Diagram
Operation
-
The PCM stops current to the A/C relay when any of the following conditions are met:
|
Operation condition |
While A/C relay not energized |
Purpose |
|
At engine start |
Approx. 4 s |
Improved startability |
|
When engine speed is 6,700 rpm or more |
Approx. 5 s elapsed since engine speed was 6,200 rpm or less |
A/C compressor reliability assurance |
|
Accelerated |
3 to 5 s |
Acceleration from standstill/acceleration performance improvement |
|
Refrigerant pressure 3.14 MPa {32.0 kgf/cm2, 455 psi} or more |
Refrigerant pressure decreases to 2.55 MPa {26.0 kgf/cm2, 370 psi} or less |
A/C compressor reliability assurance |
|
Refrigerant pressure of 0.196 MPa {2.00 kgf/cm2, 28.4 psi} or less continues for 5 s or more |
Refrigerant pressure of 0.226 MPa {2.30 kgf/cm2, 32.8 psi} or more continues to 5 s or more |
A/C compressor reliability assurance |
|
Drive-by-wire control malfunction |
— |
Reverse driving performance assurance |
|
Panic braking determined |
— |
Load performance assurance |
|
Misfire determination |
— |
Catalytic converter protection |
|
ECT sensor malfunction |
— |
Engine protection |
|
Engine coolant temperature 113 °C {235 °F} or more |
Turns on/off repeatedly every 10 s until engine coolant temperature is less than approx. 107 °C {225 °F} |
Engine protection |
|
Engine coolant temperature 117 °C {243 °F} or more |
Until engine coolant temperature is less than 110 °C {230 °F} |
Engine protection |
A/C Compressor Removal/Installation
1. Disconnect the negative battery cable..
2. Discharge the refrigerant..
3. Remove the front under cover No.2..
4. Remove the drive belt..
5. Disconnect the connector.
6. Remove bolts A ...
A/C Unit
Outline
The A/C unit which integrates the cooling and heater units has been adopted.
Construction
The A/C unit consists of the following parts.
Operation
Air Mix Door Op ...
Other materials:
Rear Wheel Hub Bolt Replacement
1. Remove the brake calliper component and suspend it out of the way using a
cable.
2. Remove the disc plate.
3. Remove the wheel hub bolt using the SST as shown in the figure.
4. Place a new wheel hub bolt in the wheel hub.
5. Install the wheel hub by placing a proper sized washer o ...
Mass Air Flow (MAF) Sensor/Intake Air Temperature (Iat) Sensor No.1 Removal/Installation
NOTE:
Because the IAT sensor No.1 is integrated in the MAF sensor, replacing the
IAT sensor No.1 includes replacement of the MAF sensor/IAT sensor No.1.
1. Disconnect the negative battery cable..
2. Disconnect the MAF sensor/IAT sensor No.1 connector.
3. Remove the MAF sensor/IA ...
Hazardous Driving
WARNING
Be extremely careful if it is necessary to downshift on slippery surfaces: Downshifting
into lower gear while driving on slippery surfaces is dangerous. The sudden change
in tire speed could cause the tires to skid.
This could lead to loss of vehicle control and an accident.
When driv ...
