Mazda CX-5 Service & Repair Manual: A/C Compressor Control [Full Auto Air Conditioner]
Purpose
-
The A/C compressor control switches the A/C compressor on/off according to the vehicle environment.
Function
-
The A/C compressor control turns the A/C compressor on/off based on the climate control unit operation and signals from each sensor.
-
The A/C compressor control has automatic and manual controls.
-
The A/C compressor automatic control performs the following correction:
-
Defroster correction
A/C compressor automatic control
-
The climate control unit determines the A/C ON/OFF mode based on the ambient temperature.
-
The climate control unit determines the A/C signal on/off according to the air conditioner operation such as A/C ON mode (A/C switch ON) or AUTO mode (AUTO switch ON).
-
In A/C ON mode, the A/C signal (magnetic clutch) on/off is determined based on the ambient temperature and the temperature of the air passing through the evaporator.
-
In AUTO mode, the A/C signal (magnetic clutch) on/off is determined based on the ambient temperature calculation value and the temperature of the air passing through the evaporator.
-
The ambient temperature calculation value is calculated based on the ambient temperature, set temperature, cabin temperature, and sunlight intensity.
-
When the ambient temperature is low, the A/C signal (magnetic clutch) OFF temperature is set lower to prevent window fogging.
A/C compressor manual control
-
The climate control unit switches the A/C ON/OFF mode according to the A/C switch operation.
|
A/C mode |
Operation condition |
|
|
A/C ON mode (A/C display) |
Fixed in A/C mode. |
|
|
A/C OFF mode (No display) |
Fixed in A/C OFF mode. |
|
Correction
-
Defroster correction
-
When the defroster switch is turned on, the system is switched to A/C ON mode to improve defogging.
Construction
-
The A/C compressor control consists of the parts indicated in the following table:
|
Input device |
Control part |
Output device |
|
|
|
Operation
1. The climate control determines the A/C ON/OFF based on the operations of each switch/dial and signals from each sensor which changes according to the vehicle environment.
2. The climate control unit sends the A/C signal to the PCM according to the result of the A/C ON/OFF determination and corrections.
3. When the PCM turns the A/C relay on based on the A/C signal, the magnetic clutch of the A/C compressor turns on.
A/C Compressor
Purpose
The A/C compressor circulates the refrigerant in the refrigerant cycle.
The A/C compressor compresses the gaseous refrigerant atomized by the evaporator,
and by pressurizing ...
A/C Compressor Removal/Installation
1. Disconnect the negative battery cable..
2. Discharge the refrigerant..
3. Remove the front under cover No.2..
4. Remove the drive belt..
5. Disconnect the connector.
6. Remove bolts A ...
Other materials:
Coupling Component Calibration Data Writing
1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the toolbox
of the M-MDS.
Select “Chassis”.
3. Then, select items from the screen menu in the following order.
Select “4WD/AWD”.
Select “Coupling Calibra ...
Initial Learning [Fw6 A EL, Fw6 Ax EL]
Introduction
If the control valve body and oil pressure switch are replaced, always perform
the initial learning. If the initial learning is not completed, engine rev-up
may occur or shift shock may increase. DTC P06B8:00 is displayed while the initial
learning has not been implement ...
Keys
WARNING
Do not leave the key in your vehicle with children and keep them in a place where
your children will not find or play with them:
•eaving children in a vehicle with the key is
dangerous. This could result in someone being badly injured or even killed. Children
may find these keys to ...
