Chevrolet Spark manuals

Audi A4 (B9) 2016-2022 Owner's Manual: Garage door opener

Description

Applies to: vehicles with garage door opener

With the garage door opener, you can activate systems such as the garage doors, security systems or house lights from inside your vehicle.

These functions are operated in the MMI. Multiple receivers can be programmed, which can control the functions of up to eight2) hand-held transmitters.

WARNING

Tips

Tips

Before you program your system to the garage door opener, first check the compatibility:

  1. Ask an authorized Audi dealer or authorized Audi Service Facility or check at www.

    homelink.com. You can also find more information about HomeLink there.

  2. You can display information about Home- Link (compatibility level/status/country code/HomeLink generation) in the MMI:
  3. Select on the home screen: VEHICLE > Settings & Service > Garage door opener > .

2) The possible number of hand-held transmitters depends on the equipment.

Operation

Applies to: vehicles with garage door opener

Requirements: the remote control transmitter must be programmed, Programming, the vehicle must be within range of the system, and the ignition must be switched on.

There are multiple options to open or close the system (such as the garage door).

If transmission was successful, the message: Send to: XXX will appear.

Programming

Applies to: vehicles with garage door opener

You can program both fixed code and rolling code systems in the MMI using the procedure that is described.

Requirement: the ignition must be switched on.

Programming the system

Applies to: MMI

Requirement: the hand transmitter must be present and the vehicle must be within range of the system (such as the garage door) that you would like to program. If you program more than three remote control transmitters, assign the first three spots to the systems that you would also like to use when driving in reverse.

With some systems, the garage door opener will be immediately available after programming.

With other systems, the garage door opener must also be synchronized.

Synchronizing1)

Requirement: the hand transmitter must already be programmed and the vehicle must be within range of the system (such as the garage door).

If the system synchronization is performed directly after the programming procedure, follow the instructions on the MMI.

If you would like to sync at a later time:

Location pairing

Applies to: vehicles with location pairing

For easier operation, you can program your system's location.

Requirements: the respective hand transmitter must be programmed and the vehicle must be located in front of the system.

If you would like to set up location pairing at another time:

Only a maximum of three systems can be displayed in the notification center. If you would like to have all systems displayed, press

Renaming programmed systems

You can rename the programmed systems according to your preferences (names may have a maximum of 10 characters).

If you would like to change the name at another time:

Deleting programmed systems

The programmed systems can be deleted individually or all at once.

Tips

Tips

1) Only applies to rolling code systems

Panoramic glass roof
Operating the pa mic glass roof and roof sunshade Applies to: vehicles with panoramic glass roof and roof sunshade Fig. 41 Headliner: panoramic glass roof and sunshade* buttons The control buttons ar ...

Lights and Vision
...

Other materials:

Rear Scuff Plate Removal/Installation
1. Take the shaded area shown in the figure, detach tab A while pulling the rear scuff plate in the direction of the arrow (1) shown in the figure, then detach hook B, clips C, pins D while pulling in the direction of the arrow (2). 2. Take the shaded area shown in the figure, detach tab E whi ...

Rear Seat Removal/Installation
CAUTION: When removing or putting in the rear seat, contact with the surrounding areas of the vehicle could cause scratches and damage. When removing or putting in the rear seat, always use two or more persons to perform the work and be careful not to scratch or damage the rear seat ...

A/C Compressor
Purpose The A/C compressor circulates the refrigerant in the refrigerant cycle. The A/C compressor compresses the gaseous refrigerant atomized by the evaporator, and by pressurizing the gaseous refrigerant, liquification by the condenser is facilitated. Function The ...

© 2016-2022 Copyright www.mcx5.org