Mazda CX-5 Service & Repair Manual: A/C Unit Disassembly/Assembly

Mazda CX-5 Service & Repair Manual / HVAC / A/C / A/C Unit Disassembly/Assembly

1. Disassemble in the order indicated in the table.

CAUTION:

If a non-specified grease is used, it may result in abnormal noise or improper operation of the links. Apply only the specified grease to each link.

2. Assemble in the reverse order of disassembly.


Step	Part name	Disassembly/assembly of main parts
Step	Part name	Heater core	Evaporator temperature sensor	Evaporator
1	Polyurethane foam	?	?	?
2	Expansion valve	?	?	?
3	Adhesive polyurethane	?	?	?
4	Drain hose	?	?	?
5	Plate (1)	X	?	?
6	Plate (2)	X	?	?
7	Heater core	X	?	?
8	Driver-side air mix actuator (Full-auto air conditioner)	?	?	?
9	Driver-side air mix link (Full-auto air conditioner)	?	?	?
10	Passenger-side air mix actuator (Full-auto air conditioner)	?	?	?
11	Passenger-side air mix link (Full-auto air conditioner)	?	?	?
12	Air mix link (Manual air conditioner)	?	?	?
13	Airflow mode actuator (Full-auto air conditioner)	?	?	?
14	Airflow mode link set	?	?	?
15	Power MOS FET (Full-auto air conditioner)	?	?	?
15	Resistor (Manual air conditioner)	?	?	?
16	A/C case (1)	?	X	X
17	A/C case (2)	?	X	X
18	Evaporator temperature sensor.	?	X	X
19	Evaporator	?	?	X
20	A/C case (3)	?	?	?
21	A/C case (4)	?	?	?
22	Door damper	?	?	?

X: Applicable

?: Not applicable

Evaporator Temperature Sensor Assembly Note

1. Assemble the evaporator temperature sensor as shown in the figure.

CAUTION:

When installing the evaporator temperature sensor without replacing the evaporator, assemble the evaporator temperature sensor with the installation position slid to the left of the previous position by 1 line. If the evaporator temperature sensor is assembled to the previously installed position, it may not function due to poor contact of the fin surface with the sensor detection area caused by fin deformation.

NOTE:

If an evaporator temperature sensor cannot be correctly positioned on the evaporator, replace the evaporator.

A/C Unit

Outline The A/C unit which integrates the cooling and heater units has been adopted. Construction The A/C unit consists of the following parts. Operation Air Mix Door Op ...

A/C Unit Removal/Installation

1. Disconnect the negative battery cable.. 2. Discharge the refrigerant.. 3. Drain the engine coolant.. CAUTION: If moisture or foreign material enters the refrigeration cycle, cooling a ...

Other materials:

Propeller Shaft On Vehicle Inspection
Joint Area Excessive Play Inspection 1. Shake the universal joint by hand and verify that there is no excessive play. 2. If there is any excessive play, replace the propeller shaft.. Propeller Shaft Runout Inspection CAUTION: Do not rotate the propeller shaft using engine force wh ...

Battery Runs Out
Jump-Starting Jump-starting is dangerous if done incorrectly. So follow the procedure carefully. If you feel unsure about jump-starting, we strongly recommend that you have a competent service technician do the work. WARNING Follow These Precautions Carefully: To ensure safe and correct ...

Panel Light
Purpose The panel light adjusts the instrument cluster and steering switch illumination brightness. Function The instrument cluster adjusts the brightness of the following illumination lights when a TNS illumination signal sent via CAN transmission from the front body co ...